From: Cecil Wilson (Cecil.Wilson@flextronics.com)
Date: Wed Dec 19 2007 - 15:11:11 ART
Hello
One of my biggest problem is been able to verify my answers, (in a
timely manner)
-Is there a link, or book etc, that would help with this issue?
-If I had to purchase 2 workbooks? Which ones would you recommended
- I just did my lab in RTP, lets just say santa was NOT good to me
Thanks for ALL suggestions
Cecil G. Wilson
IT Network Services
Office: (901) 215-2710
Cell: (901) 601-6201
VoIP 104-2710
FLEX Logistics
cecil.wilson@flextronics.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Joseph Brunner
Sent: Tuesday, December 18, 2007 11:19 AM
To: 'suri tk'; ccielab@groupstudy.com
Subject: RE: Simple IPv6 question
Is this frame-relay? Sounds like you need to map some global unicast
addresses
R1
Int s3/1
Frame-relay map ipv6 2001::2 301 broadcast
Etc.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
suri tk
Sent: Tuesday, December 18, 2007 12:03 PM
To: ccielab@groupstudy.com
Subject: Simple IPv6 question
Hi All,
I have a very simple IPv6 question.
I have two routers connected back-to-back on a serial link.
router1 (serial3/1) ------------------------------------( serial0/0/0)
router2
But i am not able to ping the global unicast address from one side to on
the other.
I think its something elementary, but not able to figure out what ?.
Please help me to understand this.
Thanks,
Surendra
========================================================================
====
=
=========
router1#sh run int ser 3/1
interface Serial3/1
no ip address
ipv6 address 2001:0:0:1::/64 eui-64
ipv6 enable
router1#sh ipv6 route
IPv6 Routing Table - 5 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS
summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext
2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
C 2001:0:0:1::/64 [0/0]
via ::, Serial3/1
L 2001::1:212:43FF:FEC9:A620/128 [0/0]
via ::, Serial3/1
L FF00::/8 [0/0]
via ::, Null0
router2#sh run int ser 0/0/0
interface Serial0/0/0
no ip address
ipv6 address 2001:0:0:2::/64 eui-64
ipv6 enable
no fair-queue
clock rate 64000
end
router2#sh ipv6 route
IPv6 Routing Table - 3 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS
summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext
2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
C 2001:0:0:2::/64 [0/0]
via ::, Serial0/0/0
L 2001::2:213:C4FF:FEDC:4CB0/128 [0/0]
via ::, Serial0/0/0
L FF00::/8 [0/0]
via ::, Null0
router2#ping ipv6 2001::1:212:43FF:FEC9:A620
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001::1:212:43FF:FEC9:A620, timeout is
2 seconds:
.....
Success rate is 0 percent (0/5)
router2#
This archive was generated by hypermail 2.1.4 : Tue Jan 01 2008 - 12:04:31 ARST