From: Calil Zorby (zorby@doglover.com)
Date: Sun Nov 18 2007 - 23:40:58 ART
No problem...I take it off
R2
!
interface Serial0/1/0.1 point-to-point
ip address 4.4.24.4 255.255.255.0
ip pim sparse-dense-mode
!
interface FastEthernet0/0
ip address 150.2.4.1 255.255.255.0
ip directed-broadcast
ip multicast helper-map broadcast 224.2.2.2 111 ttl 16
!
And I can ping, from R2, the multicast group 224.2.2.2:
R2#ping 224.2.2.2 repeat 3
Type escape sequence to abort.
Sending 3, 100-byte ICMP Echos to 224.2.2.2, timeout is 2 seconds:
Reply to request 0 from 4.4.24.2, 4 ms
Reply to request 1 from 4.4.24.2, 4 ms
Reply to request 2 from 4.4.24.2, 4 ms
R3
!
interface FastEthernet0/0
ip address 4.4.26.2 255.255.255.0
ip directed-broadcast
ip pim sparse-dense-mode
ip igmp join-group 224.2.2.2
!
interface Serial0/1/0.1 point-to-point
ip address 4.4.24.2 255.255.255.0
ip pim sparse-dense-mode
ip multicast helper-map 224.2.2.2 4.4.26.255 111
frame-relay interface-dlci 101
end
R3#debug ip mp
R3#debug ip mpacket det
R3#debug ip mpacket detail
IP multicast packets debugging is on (detailed)
R3#debug ip pa
R3#debug ip packet de
R3#debug ip packet detail 111
IP packet debugging is on (detailed) for access list 111
R3#
Nothing happened yet....
thanks
----- Original Message -----
From: "Joseph Brunner"
To: ccielab@groupstudy.com
Subject: RE: Multicast helper-map - What is wrong with it?
Date: Sun, 18 Nov 2007 21:17:12 -0500
Why is this on r2s serial?
ip pim dr-priority 0
take it off for now, and please make every interface ip pim
sparse-dense mode
then, also, make sure we are neighbored up in pim
show ip pim neighbor
do the debugs on R3 again
at the very least you should be able to ping 224.2.2.2 from R2
regardless of the helper-map
--------------------------------------------------------------------
From: Hugo Viana [mailto:zorby@doglover.com]
Sent: Sunday, November 18, 2007 9:13 PM
To: Joseph Brunner; ccielab@groupstudy.com
Subject: RE: Multicast helper-map - What is wrong with it?
R2
!
interface FastEthernet0/0
ip address 150.2.4.1 255.255.255.0
ip directed-broadcast
ip multicast helper-map broadcast 224.2.2.2 111 ttl 16
!
R2#debug ip packet detail 111
IP packet debugging is on (detailed) for access list 111
R2#
*Nov 19 02:47:01.611: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 19 02:47:01.611: UDP src=51207, dst=3434
*Nov 19 02:47:02.611: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 19 02:47:02.611: UDP src=57194, dst=3434
On R3:
R3#
R3#debug ip mpacket detail
IP multicast packets debugging is on (detailed)
R3#ter mon
% Console already monitors
R3#
Nothing happens...
Thanks!
----- Original Message -----
From: "Joseph Brunner"
To: "'Hugo Viana'" , ccielab@groupstudy.com
Subject: RE: Multicast helper-map - What is wrong with it?
Date: Sun, 18 Nov 2007 21:04:27 -0500
Go ahead and give me a ttl remap on R2s multicast helper-map command
(facing the broadcast)
So ttl 16
At the end of the map
Then lets do a #debug ip mpacket detail on R3
-Joe
--------------------------------------------------------------------
From: Hugo Viana [mailto:zorby@doglover.com]
Sent: Sunday, November 18, 2007 8:59 PM
To: Joseph Brunner; ccielab@groupstudy.com
Subject: RE: Multicast helper-map - What is wrong with it?
R2#sh ip mroute
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C -
Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 224.0.1.40), 01:05:15/stopped, RP 4.4.24.2, flags: SJPCL
Incoming interface: Serial0/1/0.1, RPF nbr 4.4.24.2
Outgoing interface list: Null
R3#sh ip mroute
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C -
Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 224.6.6.6), 07:08:26/00:03:25, RP 4.4.24.2, flags: SJC
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
FastEthernet0/0, Forward/Sparse-Dense, 07:08:09/00:03:25
(*, 224.2.2.2), 00:05:40/00:02:53, RP 4.4.24.2, flags: SJCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Serial0/1/0.1, Forward/Sparse, 00:04:53/00:00:00
FastEthernet0/0, Forward/Sparse-Dense, 00:05:41/00:02:45
(*, 224.0.1.40), 07:08:37/00:02:51, RP 4.4.24.2, flags: SJCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Serial0/1/0.1, Forward/Sparse, 01:05:11/00:02:53
FastEthernet0/0, Forward/Sparse-Dense, 07:08:37/00:02:43
R3#sh run int fa0/0
Building configuration...
Current configuration : 240 bytes
!
interface FastEthernet0/0
ip address 4.4.26.2 255.255.255.0
ip broadcast-address 4.4.26.255
ip directed-broadcast
ip pim sparse-dense-mode
ip igmp join-group 224.2.2.2
!
----- Original Message -----
From: "Joseph Brunner"
To: zorby@doglover.com, ccielab@groupstudy.com
Subject: RE: Multicast helper-map - What is wrong with it?
Date: Sun, 18 Nov 2007 20:39:16 -0500
We'll help you doglover, don't worry...
Go ahead and give me a ip igmp join-group 224.2.2.2 on R3's F0/0 and
a
Ip pim sparse-dense.
Now post back a "show ip mroute" on R2 and R3. I want to see what's
in the
Multicast O.I.L.
Thanks,
Joe
(BTW: if you want to a webex to observe this work in my lab, we can,
I
played this command for hours and hours and found several ways to get
its
functionality without the helper-map)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
zorby@doglover.com
Sent: Sunday, November 18, 2007 7:44 PM
To: ccielab@groupstudy.com
Subject: Multicast helper-map - What is wrong with it?
Hello!
I am trying to simulate the forward of broadcast traffic into
multicast
packets using the command "ip multicast helper-map", as the LAB8 of
IE.
The network is the following:
R1 (e0/0) --- (f0/0) R2 (s0/1/0.1) <--FR--> (s0/1/0.1) R3 (fa0/0) ---
(fa0/0) R4
CONFIGS:
---------------------------------------------------------------------------
-
-------
***R1 - Sender Broadcast traffic via SAA:
!
rtr 1
rtr schedule 1 life forever start-time now
!
type udpEcho dest-ipaddr 255.255.255.255 dest-port 3434 control
disable
timeout 1
frequency 1
!
***R2 - Receive broadcast and send into multicast packets to
224.2.2.2
group:
!
interface FastEthernet0/0
ip address 150.2.4.1 255.255.255.0
ip multicast helper-map broadcast 224.2.2.2 111
!
interface Serial0/1/0.1 point-to-point
ip address 4.4.24.4 255.255.255.0
ip pim dr-priority 0
ip pim sparse-mode
!
access-list 111 permit udp any any eq 3434
!
ip forward-protocol udp 3434
!
***R3 - Receive multicast traffic and send to broadcast address
(fa0/0)
!
interface Serial0/1/0.1 point-to-point
ip address 4.4.24.2 255.255.255.0
ip pim sparse-mode
ip multicast helper-map 224.2.2.2 4.4.26.255 111
!
access-list 111 permit udp any any eq 3434
!
ip forward-protocol udp 3434
!
interface FastEthernet0/0
ip address 4.4.26.2 255.255.255.0
ip directed-broadcast
ip pim sparse-mode
!
---------------------------------------------------------------------------
-
------
Verification on routers:
R1:
R1#sh rtr totals-statistics
Entry number: 1
Start Time Index: *04:25:25.046 UTC Mon Mar 1 1993
Age of statistics entry (seconds): 3034
Number of initiations: 3035
R2:
I can see the broadcast traffic on ethernet interface:
R2#debug ip packet detail 111
IP packet debugging is on (detailed) for access list 111
R2#
*Nov 18 19:53:21.187: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 18 19:53:21.187: UDP src=56958, dst=3434
*Nov 18 19:53:22.187: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 18 19:53:22.187: UDP src=49314, dst=3434
*Nov 18 19:53:23.187: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 18 19:53:23.187: UDP src=50778, dst=3434
*Nov 18 19:53:24.187: IP: s=150.2.4.254 (FastEthernet0/0),
d=255.255.255.255, len 44, rcvd 2
*Nov 18 19:53:24.187: UDP src=57531, dst=3434
But When I try to see the multicast packets:
R2#debug ip mp
R2#debug ip mpacket
IP multicast packets debugging is on
R2#
R2#
R2#
Nothing happens at all...
R3:
R3#debug ip packet detail 111
IP packet debugging is on (detailed) for access list 111
R3#
Nothing happens too...
---------------------------------------------------------------------------
-
-----
Anybody has any idea about what is wrong? Brian, could you help me?
I read everything that I found about this, but i really don't know
what is
wrong...:
- Developing IP Multicast Networks - Chapter 16 -
"Broadcast-Multicast
Traffic Conversion"
- IEWB - LAB 8 - Version 4
- "ip multicast helper-map" command:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cr/himc_
r
/mlt_i1h.htm#wp1134745
Thanks for any help,
Zorby
_______________________________________________________________________
Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
--
Over 2 Million Holiday Gift Ideas - Take a Look!
mail.com Shopping
--
Over 2 Million Holiday Gift Ideas - Take a Look!
mail.com Shopping
-- Over 2 Million Holiday Gift Ideas - Take a Look! mail.com shopping at http://mail.shopping.com/?linkin_id=8033174
This archive was generated by hypermail 2.1.4 : Sat Dec 01 2007 - 06:37:30 ART