From: Radioactive Frog (pbhatkoti@gmail.com)
Date: Sun Oct 14 2007 - 04:14:04 ART
HI Hass,
I got it sorted out out. The trick was the vwic2-1mft-e1t1 physical
interface wasn't up. so i just used a RJ45 t1 loopback connector to spoof'd
the T1 port.
Product : Cisco 2811
Gateway : S0/SU0/DS1-0@br1.ccievoice.com
Device Protocol: Digital Access PRI
Registration: Registered with Cisco CallManager 10.1.200.21 <----- Hunky
dory
IP Address: 10.10.32.2
br1#
br1#show controllers t1
T1 0/0/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
Description: ### BR1 PRI ###
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20040802, FPGA: 13, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (434 seconds elapsed):
4780 Line Code Violations, 2 Path Code Violations
2 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 421 Unavail
Secs
Total Data (last 10 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 9000 Unavail
Secs
br1#
br1#
br1#
br1#
br1#show int s0/0/0:23
Serial0/0/0:23 is up, line protocol is up (spoofing)
Hardware is DSX1
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input 00:00:02, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
56 packets input, 168 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
56 packets output, 168 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
Timeslot(s) Used:24, SCC: 0, Transmitter delay is 0 flags
br1#
br1#
On 10/14/07, Radioactive Frog <pbhatkoti@gmail.com> wrote:
>
> Actually, at this stage, the E1 is not connected physically.
>
>
> br1#show isdn
> br1#show isdn status
> Global ISDN Switchtype = primary-ni
>
> %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may
> not appl
> y
>
> ISDN Serial0/0/0:23 interface
> dsl 0, interface ISDN Switchtype = primary-ni
> L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
> Layer 1 Status:
> DEACTIVATED
> Layer 2 Status:
> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x00000000
> Number of L2 Discards = 0, L2 Session ID = 0
> Total Allocated ISDN CCBs = 0
> br1#
> br1#
>
>
> On 10/14/07, Haas, Brad <bhaas@presidio.com> wrote:
> >
> > What Is your isdn status? Are multiple frames established?
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Radioactive Frog
> > Sent: Sunday, October 14, 2007 1:00 AM
> > To: Cisco certification; Cisco certification
> > Subject: 2811 as a mgcp gateway in ccm4.1 registration issue
> >
> > Registration: Not RegisteredHi guys,
> > Trying to add the mgcp gateway in CCM4.1 but having some issues.
> >
> > The router shows gateway is registered with ccm but CCM doesn't show
> > registration status. Any status?
> >
> > Any thought appreciated.
> >
> > --------------On CCM---this is the status-------------------------
> > Product : Cisco 2811
> > Gateway : S0/SU0/DS1-0@br1.ccievoice.com
> > Device Protocol: Digital Access PRI
> > Registration: Not Registered <---------------?????????????????
> > IP Address: 10.10.32.2
> >
> >
> > br1#
> > br1#show ccm-manager
> > MGCP Domain Name: br1.ccievoice.com
> > Priority Status Host
> > ============================================================
> > Primary Registered 10.1.200.21
> > <---------------Register
> > First Backup None
> > Second Backup None
> >
> > Current active Call Manager: 10.1.200.21
> > Backhaul/Redundant link port: 2428
> > Failover Interval: 30 seconds
> > Keepalive Interval: 15 seconds
> > Last keepalive sent: 03:57:03 UTC Oct 14 2007 (elapsed time:
> > 00:00:12
> > )
> > Last MGCP traffic time: 03:57:03 UTC Oct 14 2007 (elapsed time:
> > 00:00:12
> > )
> > Last failover time: None
> > Last switchback time: None
> > Switchback mode: Immediate
> > MGCP Fallback mode: Enabled/OFF
> > Last MGCP Fallback start time: 03:42:10 UTC Oct 14 2007
> > Last MGCP Fallback end time: 03:52:41 UTC Oct 14 2007
> > MGCP Download Tones: Disabled
> >
> > Backhaul Link info:
> > Link Protocol: TCP
> > Remote Port Number: 2428
> > Remote IP Address: 10.1.200.21
> > Current Link State: OPEN
> > Statistics:
> > Packets recvd: 0
> > Recv failures: 0
> > Packets xmitted: 0
> > Xmit failures: 0
> > PRI Ports being backhauled:
> > Slot 0, port 0
> > FAX mode: disable
> > Configuration Error History:
> > br1#
> >
> >
> >
> >
> >
> >
> > show run of br1:
> >
> >
> > br1#
> > br1#
> > br1#
> > br1#
> > br1#
> > br1#
> > br1#sh run
> > Building configuration...
> >
> > Current configuration : 4287 bytes
> > !
> > version 12.4
> > service timestamps debug datetime msec
> > service timestamps log datetime msec
> > no service password-encryption
> > !
> > hostname br1
> > !
> > boot-start-marker
> > boot-end-marker
> > !
> > card type t1 0 0
> > enable password cisco
> > !
> > no aaa new-model
> > !
> > resource policy
> > !
> > network-clock-participate wic 0
> > ip subnet-zero
> > !
> > !
> > ip cef
> > !
> > !
> > no ip domain lookup
> > ip domain name ccievoice.com
> > ip host HO 10.10.32.1
> > ip host BR1 10.10.32.2
> > ip host BR2 10.10.32.3
> > ip host HQSW 10.1.200.100
> > frame-relay switching
> > isdn switch-type primary-ni
> > !
> > voice-card 0
> > no dspfarm
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > controller T1 0/0/0
> > framing esf
> > linecode b8zs
> > pri-group timeslots 1-3,24 service mgcp
> > description ### BR1 PRI ###
> > !
> > !
> > !
> > !
> > interface Loopback0
> > ip address 10.10.32.2 255.255.255.255
> > ip ospf network point-to-point
> > !
> > interface FastEthernet0/0
> > no ip address
> > ip helper-address 10.1.200.21
> > shutdown
> > duplex auto
> > speed auto
> > !
> > interface FastEthernet0/1
> > no ip address
> > shutdown
> > duplex auto
> > speed auto
> > !
> > interface Serial0/0/0:23
> > no ip address
> > encapsulation hdlc
> > no logging event link-status
> > isdn switch-type primary-ni
> > isdn incoming-voice voice
> > isdn bind-l3 ccm-manager
> > isdn bchan-number-order ascending
> > no cdp enable
> > !
> > interface Serial0/1/0
> > no ip address
> > encapsulation frame-relay IETF
> > ip ospf mtu-ignore
> > no fair-queue
> > clock rate 128000
> > frame-relay lmi-type ansi
> > frame-relay intf-type dce
> > !
> > interface Serial0/1/0.1 point-to-point
> > ip address 10.10.33.2 255.255.255.128
> > ip ospf mtu-ignore
> > no keepalive
> > frame-relay interface-dlci 101
> > !
> > interface FastEthernet1/0
> > description --- l3 interfaces for others --
> > no switchport
> > no ip address
> > !
> > interface FastEthernet1/1
> > description ### BR1 phone1 ###
> > switchport trunk native vlan 20
> > switchport mode trunk
> > switchport voice vlan 120
> > spanning-tree portfast
> > !
> > interface FastEthernet1/2
> > description ### BR1 phone2 ###
> > switchport trunk native vlan 20
> > switchport mode trunk
> > switchport voice vlan 120
> > !
> > interface FastEthernet1/3
> > description #### not in use so shutdown ###
> > !
> > interface FastEthernet1/4
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/5
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/6
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/7
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/8
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/9
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/10
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/11
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/12
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/13
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/14
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface FastEthernet1/15
> > description #### not in use so shutdown ###
> > shutdown
> > !
> > interface Vlan1
> > no ip address
> > !
> > interface Vlan20
> > description ### Data VLAN ###
> > ip address 10.20.0.1 255.255.255.0
> > ip helper-address 10.1.200.21
> > !
> > interface Vlan120
> > description ### Voice VLAN ###
> > ip address 10.120.0.1 255.255.255.0
> > ip helper-address 10.1.200.21
> > !
> > router ospf 1
> > log-adjacency-changes
> > network 10.10.32.2 0.0.0.0 area 0
> > network 10.10.33.0 0.0.0.127 area 0
> > network 10.20.0.0 0.0.0.255 area 0
> > network 10.120.0.0 0.0.0.255 area 0
> > !
> > ip classless
> > !
> > no ip http server
> > !
> > !
> > !
> > !
> > control-plane
> > !
> > !
> > !
> > voice-port 0/0/0:23
> > !
> > ccm-manager switchback immediate
> > ccm-manager fallback-mgcp
> > ccm-manager mgcp
> > no ccm-manager fax protocol cisco
> > ccm-manager music-on-hold
> > !
> > mgcp
> > mgcp call-agent 10.1.200.21 service-type mgcp version 0.1
> > mgcp dtmf-relay voip codec all mode cisco
> > mgcp modem passthrough voip mode nse
> > mgcp ip qos dscp cs3 signaling
> > mgcp bind control source-interface Loopback0
> > mgcp bind media source-interface Loopback0
> > !
> > mgcp profile default
> > source interface Loopback0
> > !
> > !
> > !
> > dial-peer voice 99 pots
> > service mgcpapp
> > incoming called-numeber
> > port 0/0/0:23
> >
> > line con 0
> > exec-timeout 0 0
> > line aux 0
> > line vty 0 4
> > exec-timeout 0 0
> > password cisco
> > login
> > !
> > scheduler allocate 20000 1000
> > !
> > end
> >
> > br1#
> > br1#
> > br1#
> > br1#
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Nov 16 2007 - 13:11:14 ART