From: Radioactive Frog (pbhatkoti@gmail.com)
Date: Sun Oct 14 2007 - 05:31:11 ART
Just if someone would like to dig on this little more...
Can anyone point me in the right direction re how to troubleshoot this
problem?
Where on CCM i should be looking for errors which tells me there is no cable
plugged into ?
On 10/14/07, Radioactive Frog <pbhatkoti@gmail.com> wrote:
>
> HI Hass,
> I got it sorted out out. The trick was the vwic2-1mft-e1t1 physical
> interface wasn't up. so i just used a RJ45 t1 loopback connector to spoof'd
> the T1 port.
>
>
> Product : Cisco 2811
> Gateway : S0/SU0/DS1-0@br1.ccievoice.com
> Device Protocol: Digital Access PRI
> Registration: Registered with Cisco CallManager 10.1.200.21 <----- Hunky
> dory
> IP Address: 10.10.32.2
>
> br1#
> br1#show controllers t1
> T1 0/0/0 is up.
> Applique type is Channelized T1
> Cablelength is long gain36 0db
> Description: ### BR1 PRI ###
> No alarms detected.
> alarm-trigger is not set
> Soaking time: 3, Clearance time: 10
> AIS State:Clear LOS State:Clear LOF State:Clear
> Version info Firmware: 20040802, FPGA: 13, spm_count = 0
> Framing is ESF, Line Code is B8ZS, Clock Source is Line.
> CRC Threshold is 320. Reported from firmware is 320.
> Data in current interval (434 seconds elapsed):
> 4780 Line Code Violations, 2 Path Code Violations
> 2 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
> 2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 421 Unavail
> Secs
> Total Data (last 10 15 minute intervals):
> 0 Line Code Violations, 0 Path Code Violations,
> 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
> 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 9000 Unavail
> Secs
> br1#
> br1#
>
> br1#
> br1#
> br1#show int s0/0/0:23
> Serial0/0/0:23 is up, line protocol is up (spoofing)
> Hardware is DSX1
> MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation HDLC, loopback not set
> Last input 00:00:02, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/1/256 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> Available Bandwidth 48 kilobits/sec
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 56 packets input, 168 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 56 packets output, 168 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 1 carrier transitions
> Timeslot(s) Used:24, SCC: 0, Transmitter delay is 0 flags
> br1#
> br1#
>
>
>
>
>
> On 10/14/07, Radioactive Frog <pbhatkoti@gmail.com> wrote:
> >
> > Actually, at this stage, the E1 is not connected physically.
> >
> >
> > br1#show isdn
> > br1#show isdn status
> > Global ISDN Switchtype = primary-ni
> >
> > %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may
> > not appl
> > y
> >
> > ISDN Serial0/0/0:23 interface
> > dsl 0, interface ISDN Switchtype = primary-ni
> > L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
> > Layer 1 Status:
> > DEACTIVATED
> > Layer 2 Status:
> > TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Active dsl 0 CCBs = 0
> > The Free Channel Mask: 0x00000000
> > Number of L2 Discards = 0, L2 Session ID = 0
> > Total Allocated ISDN CCBs = 0
> > br1#
> > br1#
> >
> >
> > On 10/14/07, Haas, Brad <bhaas@presidio.com > wrote:
> > >
> > > What Is your isdn status? Are multiple frames established?
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> > > Of
> > > Radioactive Frog
> > > Sent: Sunday, October 14, 2007 1:00 AM
> > > To: Cisco certification; Cisco certification
> > > Subject: 2811 as a mgcp gateway in ccm4.1 registration issue
> > >
> > > Registration: Not RegisteredHi guys,
> > > Trying to add the mgcp gateway in CCM4.1 but having some issues.
> > >
> > > The router shows gateway is registered with ccm but CCM doesn't show
> > > registration status. Any status?
> > >
> > > Any thought appreciated.
> > >
> > > --------------On CCM---this is the status-------------------------
> > > Product : Cisco 2811
> > > Gateway : S0/SU0/DS1-0@br1.ccievoice.com
> > > Device Protocol: Digital Access PRI
> > > Registration: Not Registered <---------------?????????????????
> > > IP Address: 10.10.32.2
> > >
> > >
> > > br1#
> > > br1#show ccm-manager
> > > MGCP Domain Name: br1.ccievoice.com
> > > Priority Status Host
> > > ============================================================
> > > Primary Registered 10.1.200.21
> > > <---------------Register
> > > First Backup None
> > > Second Backup None
> > >
> > > Current active Call Manager: 10.1.200.21
> > > Backhaul/Redundant link port: 2428
> > > Failover Interval: 30 seconds
> > > Keepalive Interval: 15 seconds
> > > Last keepalive sent: 03:57:03 UTC Oct 14 2007 (elapsed
> > > time:
> > > 00:00:12
> > > )
> > > Last MGCP traffic time: 03:57:03 UTC Oct 14 2007 (elapsed
> > > time:
> > > 00:00:12
> > > )
> > > Last failover time: None
> > > Last switchback time: None
> > > Switchback mode: Immediate
> > > MGCP Fallback mode: Enabled/OFF
> > > Last MGCP Fallback start time: 03:42:10 UTC Oct 14 2007
> > > Last MGCP Fallback end time: 03:52:41 UTC Oct 14 2007
> > > MGCP Download Tones: Disabled
> > >
> > > Backhaul Link info:
> > > Link Protocol: TCP
> > > Remote Port Number: 2428
> > > Remote IP Address: 10.1.200.21
> > > Current Link State: OPEN
> > > Statistics:
> > > Packets recvd: 0
> > > Recv failures: 0
> > > Packets xmitted: 0
> > > Xmit failures: 0
> > > PRI Ports being backhauled:
> > > Slot 0, port 0
> > > FAX mode: disable
> > > Configuration Error History:
> > > br1#
> > >
> > >
> > >
> > >
> > >
> > >
> > > show run of br1:
> > >
> > >
> > > br1#
> > > br1#
> > > br1#
> > > br1#
> > > br1#
> > > br1#
> > > br1#sh run
> > > Building configuration...
> > >
> > > Current configuration : 4287 bytes
> > > !
> > > version 12.4
> > > service timestamps debug datetime msec
> > > service timestamps log datetime msec
> > > no service password-encryption
> > > !
> > > hostname br1
> > > !
> > > boot-start-marker
> > > boot-end-marker
> > > !
> > > card type t1 0 0
> > > enable password cisco
> > > !
> > > no aaa new-model
> > > !
> > > resource policy
> > > !
> > > network-clock-participate wic 0
> > > ip subnet-zero
> > > !
> > > !
> > > ip cef
> > > !
> > > !
> > > no ip domain lookup
> > > ip domain name ccievoice.com
> > > ip host HO 10.10.32.1
> > > ip host BR1 10.10.32.2
> > > ip host BR2 10.10.32.3
> > > ip host HQSW 10.1.200.100
> > > frame-relay switching
> > > isdn switch-type primary-ni
> > > !
> > > voice-card 0
> > > no dspfarm
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > !
> > > controller T1 0/0/0
> > > framing esf
> > > linecode b8zs
> > > pri-group timeslots 1-3,24 service mgcp
> > > description ### BR1 PRI ###
> > > !
> > > !
> > > !
> > > !
> > > interface Loopback0
> > > ip address 10.10.32.2 255.255.255.255
> > > ip ospf network point-to-point
> > > !
> > > interface FastEthernet0/0
> > > no ip address
> > > ip helper-address 10.1.200.21
> > > shutdown
> > > duplex auto
> > > speed auto
> > > !
> > > interface FastEthernet0/1
> > > no ip address
> > > shutdown
> > > duplex auto
> > > speed auto
> > > !
> > > interface Serial0/0/0:23
> > > no ip address
> > > encapsulation hdlc
> > > no logging event link-status
> > > isdn switch-type primary-ni
> > > isdn incoming-voice voice
> > > isdn bind-l3 ccm-manager
> > > isdn bchan-number-order ascending
> > > no cdp enable
> > > !
> > > interface Serial0/1/0
> > > no ip address
> > > encapsulation frame-relay IETF
> > > ip ospf mtu-ignore
> > > no fair-queue
> > > clock rate 128000
> > > frame-relay lmi-type ansi
> > > frame-relay intf-type dce
> > > !
> > > interface Serial0/1/0.1 point-to-point
> > > ip address 10.10.33.2 255.255.255.128
> > > ip ospf mtu-ignore
> > > no keepalive
> > > frame-relay interface-dlci 101
> > > !
> > > interface FastEthernet1/0
> > > description --- l3 interfaces for others --
> > > no switchport
> > > no ip address
> > > !
> > > interface FastEthernet1/1
> > > description ### BR1 phone1 ###
> > > switchport trunk native vlan 20
> > > switchport mode trunk
> > > switchport voice vlan 120
> > > spanning-tree portfast
> > > !
> > > interface FastEthernet1/2
> > > description ### BR1 phone2 ###
> > > switchport trunk native vlan 20
> > > switchport mode trunk
> > > switchport voice vlan 120
> > > !
> > > interface FastEthernet1/3
> > > description #### not in use so shutdown ###
> > > !
> > > interface FastEthernet1/4
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/5
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/6
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/7
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/8
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/9
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/10
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/11
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/12
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/13
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/14
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface FastEthernet1/15
> > > description #### not in use so shutdown ###
> > > shutdown
> > > !
> > > interface Vlan1
> > > no ip address
> > > !
> > > interface Vlan20
> > > description ### Data VLAN ###
> > > ip address 10.20.0.1 255.255.255.0
> > > ip helper-address 10.1.200.21
> > > !
> > > interface Vlan120
> > > description ### Voice VLAN ###
> > > ip address 10.120.0.1 255.255.255.0
> > > ip helper-address 10.1.200.21
> > > !
> > > router ospf 1
> > > log-adjacency-changes
> > > network 10.10.32.2 0.0.0.0 area 0
> > > network 10.10.33.0 0.0.0.127 area 0
> > > network 10.20.0.0 0.0.0.255 area 0
> > > network 10.120.0.0 0.0.0.255 area 0
> > > !
> > > ip classless
> > > !
> > > no ip http server
> > > !
> > > !
> > > !
> > > !
> > > control-plane
> > > !
> > > !
> > > !
> > > voice-port 0/0/0:23
> > > !
> > > ccm-manager switchback immediate
> > > ccm-manager fallback-mgcp
> > > ccm-manager mgcp
> > > no ccm-manager fax protocol cisco
> > > ccm-manager music-on-hold
> > > !
> > > mgcp
> > > mgcp call-agent 10.1.200.21 service-type mgcp version 0.1
> > > mgcp dtmf-relay voip codec all mode cisco
> > > mgcp modem passthrough voip mode nse
> > > mgcp ip qos dscp cs3 signaling
> > > mgcp bind control source-interface Loopback0
> > > mgcp bind media source-interface Loopback0
> > > !
> > > mgcp profile default
> > > source interface Loopback0
> > > !
> > > !
> > > !
> > > dial-peer voice 99 pots
> > > service mgcpapp
> > > incoming called-numeber
> > > port 0/0/0:23
> > >
> > > line con 0
> > > exec-timeout 0 0
> > > line aux 0
> > > line vty 0 4
> > > exec-timeout 0 0
> > > password cisco
> > > login
> > > !
> > > scheduler allocate 20000 1000
> > > !
> > > end
> > >
> > > br1#
> > > br1#
> > > br1#
> > > br1#
> > >
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Nov 16 2007 - 13:11:14 ART