From: Radioactive Frog (pbhatkoti@gmail.com)
Date: Fri Aug 17 2007 - 08:56:30 ART
Hi Theo,
It looks like it is a known problem:
The Gigabit Ethernet ports 1 to 16 (gibabitethernet0/1 to
gibabitethernet0/16) are internal interfaces that provide communication
between the switch and the blade server. These interfaces operate at 1000
Mbps, full-duplex, and use the 1000BASE-X protocol.
If the Onboard Administrator detects a physical problem between the blade
server and the switch, the Onboard Administrator changes these interfaces to
the EKEY error-disabled state. You must use the Onboard Administrator to
find the root cause of the problem, and to recover from the error-disabled
state. See the HP BladeSystem documentation at
http://www.hp.com/go/bladesystem/documentation
for more information <http://www.hp.com/go/bladesystem/documentation>.
Source:
http://www.cisco.com/en/US/products/ps6748/products_configuration_guide_chapter09186a0080814419.html
Frog
On 8/17/07, Theo M <theorack@gmail.com> wrote:
>
> Hello guys,
>
> If anybody is wondering what that means on a WS-CBS3020-HPQ,
> it simply says there in no server blade connected there, so the internal
> ports
> just go to errdisable.
>
> --
>
> >>>
> Sw-HP-Blade#
> 1d14h: %PM-4-ERR_DISABLE: ekey error detected on Gi0/5, putting Gi0/5 in
> err-disable state
> 1d14h: %PM-4-ERR_DISABLE: ekey error detected on Gi0/6, putting Gi0/6 in
> err-disable state
> 1d14h: %PM-4-ERR_DISABLE: ekey error detected on Gi0/7, putting Gi0/7 in
> err-disable state
> 1d14h: %PM-4-ERR_DISABLE: ekey error detected on Gi0/8, putting Gi0/8 in
> err-disable state
> Sw-HP-Blade#
> Sw-HP-Blade#
> 1d14h: %SYS-5-CONFIG_I: Configured from console by vty0 (10.101.96.2)
> 1d14h: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to down
> 1d14h: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to down
> 1d14h: %LINK-3-UPDOWN: Interface GigabitEthernet0/7, changed state to down
> 1d14h: %LINK-3-UPDOWN: Interface GigabitEthernet0/8, changed state to down
> Sw-HP-Blade#
> Sw-HP-Blade#
> Sw-HP-Blade#
>
> Sw-HP-Blade#sh ver
> Cisco IOS Software, CBS30X0 Software (CBS30X0-LANBASE-M), Version 12.2
> (37)SE1,
> RELEASE SOFTWARE (fc1)
> Copyright (c) 1986-2007 by Cisco Systems, Inc.
> Compiled Thu 05-Jul-07 19:54 by antonino
> Image text-base: 0x00003000, data-base: 0x00C80000
>
> ROM: Bootstrap program is CBS30X0 boot loader
> BOOTLDR: CBS30X0 Boot Loader (CBS30X0-HBOOT-M) Version 12.2(25r)SEF3,
> RELEASE SOFTWARE (fc1)
>
> Sw-HP-Blade uptime is 1 day, 14 hours, 45 minutes
> System returned to ROM by power-on
> System image file is "flash:cbs30x0-lanbase-mz.122-37.SE1/cbs30x0-
> lanbase-mz.122-37.SE1.bin"
>
> cisco WS-CBS3020-HPQ (PowerPC405) processor (revision D0) with
> 118784K/12280K bytes of memory.
> Processor board ID FOC1112T06K
> Last reset from power-on
> 1 Virtual Ethernet interface
> 1 FastEthernet interface
> 24 Gigabit Ethernet interfaces
> The password-recovery mechanism is enabled.
>
> ...
>
> Switch Ports Model SW Version SW
> Image
> ------ ----- ----- ----------
> ----------
> * 1 24 WS-CBS3020-HPQ 12.2(37)SE1
> CBS30X0-LANBASE-M
>
>
> Configuration register is 0xF
>
> Sw-HP-Blade#
> <<<
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:11 ART