From: CCIE 19999 (ccie@iprimus.com.au)
Date: Fri Aug 10 2007 - 18:45:13 ART
Herbert,
Even if the DLCI's does not match on both the ends, you can configure frame-
relay local-dlci command and it will work. See below:
R2(config-if)#
interface Serial0/1
ip address 10.10.10.2 255.255.255.0
encapsulation frame-relay
no keepalive
no dce-terminal-timing-enable
frame-relay map ip 10.10.10.5 205
no frame-relay inverse-arp
frame-relay local-dlci 502
end
R2(config-if)#do sh fram map
Serial0/1 (up): ip 10.10.10.5 dlci 205(0xCD,0x30D0), static,
CISCO
R2(config-if)#do ping 10.10.10.5
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.5, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/30/32 ms
R5(config-if)#
interface Serial0/0
ip address 10.10.10.5 255.255.255.0
encapsulation frame-relay
no keepalive
clock rate 64000
no dce-terminal-timing-enable
frame-relay map ip 10.10.10.2 502
no frame-relay inverse-arp
frame-relay local-dlci 205
end
R5(config-if)#do sh fram map
Serial0/0 (up): ip 10.10.10.2 dlci 502(0x1F6,0x7C60), static,
CISCO
R5(config-if)#do ping 10.10.10.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms
HTH
Shine
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Herbert Maosa
Sent: Saturday, 11 August 2007 12:38 AM
To: tom sun
Cc: Antonio Soares; Gadad, Milind; ccielab@groupstudy.com
Subject: Re: MFR interface - frame-relay encapsulation
You can configure back to back frame-relay between routers. You DO NOT have
to configure Frame-Relay Switching at all on any one of the routers. You
just need to remember to set one side as Frame-relay intf-typ dce and the
other as frame-relay intf-fype dte. also set your layer one clock rates.
The only caveat with back to back frame relay is that the DLCI numbers on
both sides MUST MATCH.
I have done this so many times.
Herbert.
On 8/10/07, tom sun <tomsun2007@gmail.com> wrote:
>
> i think ,if 2 routers use back-to-back mode to connect themselves .it
> does
> not support frame-relay encapsulation ,maybe you can select hdlc or ppp
> !!!
>
>
> On 8/9/07, Antonio Soares <amsoares@netcabo.pt> wrote:
> >
> > I have here a working config. I used dynamips:
> >
> > +++++++++++++++++++++++++++++
> > R1:
> > !
> > interface MFR12
> > no ip address
> > frame-relay intf-type dce
> > !
> > interface MFR12.1 point-to-point
> > ip address 12.12.12.1 255.255.255.0
> > frame-relay interface-dlci 102
> > !
> > interface Serial1/0
> > no ip address
> > encapsulation frame-relay MFR12
> > serial restart-delay 0
> > no arp frame-relay
> > !
> > interface Serial1/1
> > no ip address
> > encapsulation frame-relay MFR12
> > serial restart-delay 0
> > no arp frame-relay
> > !
> > +++++++++++++++++++++++++++++
> > R2:
> > !
> > interface MFR12
> > no ip address
> > !
> > interface MFR12.1 point-to-point
> > ip address 12.12.12.2 255.255.255.0
> > frame-relay interface-dlci 102
> > !
> > interface Serial1/0
> > no ip address
> > encapsulation frame-relay MFR12
> > serial restart-delay 0
> > no arp frame-relay
> > !
> > interface Serial1/1
> > no ip address
> > encapsulation frame-relay MFR12
> > serial restart-delay 0
> > no arp frame-relay
> > !
> > +++++++++++++++++++++++++++++
> > R1#
> > R1#ping 12.12.12.2
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 12.12.12.2, timeout is 2 seconds:
> > !!!!!
> > Success rate is 100 percent (5/5), round-trip min/avg/max = 92/122/192
> ms
> > R1#
> > +++++++++++++++++++++++++++++
> > R1#sh frame multi
> > Bundle: MFR12, State = up, class = A, fragmentation disabled
> > BID = MFR12
> > Bundle links:
> > Serial1/1, HW state = up, link state = Up, LID = Serial1/1
> > Serial1/0, HW state = up, link state = Up, LID = Serial1/0
> >
> > R1#
> > +++++++++++++++++++++++++++++
> >
> >
> > Regards,
> >
> > Antonio Soares
> > CCIE #18473, CCNP, CCIP
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Gadad, Milind
> > Sent: quinta-feira, 9 de Agosto de 2007 18:05
> > To: ccielab@groupstudy.com
> > Subject: MFR interface - frame-relay encapsulation
> >
> > Can we connect 2 routers back to back with frame-relay encapsulation? I
> > don't have a frame-rely switch in between the two routers.
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
-- Kindest regards, hm
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:10 ART