From: tom sun (tomsun2007@gmail.com)
Date: Fri Aug 10 2007 - 01:00:53 ART
i think ,if 2 routers use back-to-back mode to connect themselves .it does
not support frame-relay encapsulation ,maybe you can select hdlc or ppp !!!
On 8/9/07, Antonio Soares <amsoares@netcabo.pt> wrote:
>
> I have here a working config. I used dynamips:
>
> +++++++++++++++++++++++++++++
> R1:
> !
> interface MFR12
> no ip address
> frame-relay intf-type dce
> !
> interface MFR12.1 point-to-point
> ip address 12.12.12.1 255.255.255.0
> frame-relay interface-dlci 102
> !
> interface Serial1/0
> no ip address
> encapsulation frame-relay MFR12
> serial restart-delay 0
> no arp frame-relay
> !
> interface Serial1/1
> no ip address
> encapsulation frame-relay MFR12
> serial restart-delay 0
> no arp frame-relay
> !
> +++++++++++++++++++++++++++++
> R2:
> !
> interface MFR12
> no ip address
> !
> interface MFR12.1 point-to-point
> ip address 12.12.12.2 255.255.255.0
> frame-relay interface-dlci 102
> !
> interface Serial1/0
> no ip address
> encapsulation frame-relay MFR12
> serial restart-delay 0
> no arp frame-relay
> !
> interface Serial1/1
> no ip address
> encapsulation frame-relay MFR12
> serial restart-delay 0
> no arp frame-relay
> !
> +++++++++++++++++++++++++++++
> R1#
> R1#ping 12.12.12.2
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 12.12.12.2, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 92/122/192 ms
> R1#
> +++++++++++++++++++++++++++++
> R1#sh frame multi
> Bundle: MFR12, State = up, class = A, fragmentation disabled
> BID = MFR12
> Bundle links:
> Serial1/1, HW state = up, link state = Up, LID = Serial1/1
> Serial1/0, HW state = up, link state = Up, LID = Serial1/0
>
> R1#
> +++++++++++++++++++++++++++++
>
>
> Regards,
>
> Antonio Soares
> CCIE #18473, CCNP, CCIP
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Gadad, Milind
> Sent: quinta-feira, 9 de Agosto de 2007 18:05
> To: ccielab@groupstudy.com
> Subject: MFR interface - frame-relay encapsulation
>
> Can we connect 2 routers back to back with frame-relay encapsulation? I
> don't have a frame-rely switch in between the two routers.
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:10 ART