From: Djerk Geurts (djerk@djerk.nl)
Date: Sun Aug 05 2007 - 11:31:31 ART
Have a look at SR 606531639 "OSPF neighbors not shown in running config"...
Djerk
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> Behalf Of Carlos glez
> Sent: zondag 5 augustus 2007 8:42
> To: ccielab@groupstudy.com
> Subject: OSPF question
>
> Hi GS,
>
> I have a tiny problem that i cannot find the easy way out,
> basically I am
> just trying to get an ospf neigh up on a ethernet segmet but
> using network
> type non-brodacast
> everytime i try to get the command neigh x.x.x.x under the
> ospf process i
> get the error that the int is not NBMA, but if you see the sh
> ip ospf int ,
> it is non-brodcast
> have any of you guys have faced this, i might be missing
> something really
> basic, any help wiill be great, below are the configs ( this
> exercise is in
> IEwoorkbook lab1 version 3)
>
>
> I did found that if i dont have a virtual link configured
> going across that
> interface there is no problem.
>
>
>
> R5
> router ospf 1
> router-id 150.1.5.5
> log-adjacency-changes
> area 45 virtual-link 150.1.4.4<------
> redistribute eigrp 100 subnets
> network 150.1.5.5 0.0.0.0 area 0
> network 183.1.0.5 0.0.0.0 area 0
> network 183.1.45.5 0.0.0.0 area 45
>
>
> interface FastEthernet0/1
> ip address 183.1.45.5 255.255.255.0
> ip ospf network non-broadcast
> ip ospf cost 65
> duplex auto
> speed auto
> end
>
> FastEthernet0/1 is up, line protocol is up
> Internet Address 183.1.45.5/24, Area 45
> Process ID 1, Router ID 150.1.5.5, Network Type NON_BROADCAST, Cost:
> 65<----
> Transmit Delay is 1 sec, State WAITING, Priority 1
> No designated router on this network
> No backup designated router on this network
> Timer intervals configured, Hello 30, Dead 120, Wait 120,
> Retransmit 5
> oob-resync timeout 120
> Hello due in 00:00:27
> Wait time before Designated router selection 00:00:57
> Index 1/4, flood queue length 0
> Next 0x0(0)/0x0(0)
> Last flood scan length is 1, maximum is 7
> Last flood scan time is 0 msec, maximum is 4 msec
> Neighbor Count is 0, Adjacent neighbor count is 0
> Suppress hello for 0 neighbor(s
>
> R5(config-if)#router ospf 1
> R5(config-router)#neighbor 183.1.45.4
> OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
> R5(config-router)#
>
> both router running Version 12.3(20)
>
>
> R4(config-if)#do sh run int fas0/0
>
> !
> interface FastEthernet0/0
> ip address 183.1.45.4 255.255.255.0
> ip ospf network non-broadcast
> ip ospf cost 65
> duplex auto
> speed auto
> end
>
> FastEthernet0/0 is up, line protocol is up
> Internet Address 183.1.45.4/24, Area 45
> Process ID 1, Router ID 150.1.4.4, Network Type
> NON_BROADCAST, Cost: 65
> Transmit Delay is 1 sec, State DR, Priority 1
> Designated Router (ID) 150.1.4.4, Interface address 183.1.45.4
> No backup designated router on this network
> Timer intervals configured, Hello 30, Dead 120, Wait 120,
> Retransmit 5
> oob-resync timeout 120
> Hello due in 00:00:20
> Index 1/4, flood queue length 0
> Next 0x0(0)/0x0(0)
> Last flood scan length is 1, maximum is 7
> Last flood scan time is 0 msec, maximum is 4 msec
> Neighbor Count is 0, Adjacent neighbor count is 0
> Suppress hello for 0 neighbor(s)
>
>
> router ospf 1
> router-id 150.1.4.4
> log-adjacency-changes
> area 45 virtual-link 150.1.5.5
> network 150.1.4.4 0.0.0.0 area 0
> network 183.1.0.4 0.0.0.0 area 0
> network 183.1.45.4 0.0.0.0 area 45
> network 183.1.46.4 0.0.0.0 area 46
>
> R4(config-if)#router ospf 1
> R4(config-router)#neigh 183.1.45.5
> OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
> R4(config-router)#
>
>
>
> cheers!!
>
> JC
> <ccielab@groupstudy.com>
>
> ______________________________________________________________
> _________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:09 ART