From: brajesh.thakur@wipro.com
Date: Thu Jul 05 2007 - 05:17:15 ART
IOS 12.4(3g)
Router 3660
I also checked ipv6 command reference guide for ios 12.4, it shows only
the frame-relay map command for ipv6, but on my router I am able to
configure "frame-relay inverse-arp ipv6 102" although it doesn't work.
I also saw some documentations saying that inverse-arp is not supported
for ipv6. I don't know why did cisco include the command in router cli.
Regards,
Brajesh Thakur
-----Original Message-----
From: Navin MS [mailto:navin_ms07@yahoo.com]
Sent: Thursday, July 05, 2007 1:43 PM
To: Brajesh Thakur (WI01 - Services); mohammed.khasawneh@gmail.com;
ccielab@groupstudy.com
Subject: RE: Frame-relay inverse-arp for IPV6
Per Cisco DocCD, FR inverse-arp is supported for the following
protocols.
appletalk, decnet, ip, and ipx.
BTW, which IOS image are you running and on which router model ?
--- brajesh.thakur@wipro.com wrote:
> Thanks mate, I also thought so but my doubt is why do they included
the
> command "frame-relay inverse-arp ipv6 <dlci>" on interface level.
>
> Warm Regards,
> Brajesh Thakur
>
> -----Original Message-----
> From: Mohammed Khasawneh [mailto:mohammed.khasawneh@gmail.com]
> Sent: Thursday, July 05, 2007 1:21 PM
> To: Brajesh Thakur (WI01 - Services); ccielab@groupstudy.com
> Subject: Re: Frame-relay inverse-arp for IPV6
>
> Hi Brajesh
>
> Frame-relay dynamic mapping is not support Ipv6
> you have to configure the mapping manually !
>
> Regards
>
> ----- Original Message -----
> From: <brajesh.thakur@wipro.com>
> To: <ccielab@groupstudy.com>
> Sent: Thursday, July 05, 2007 10:43 AM
> Subject: Frame-relay inverse-arp for IPV6
>
>
> > Dear All,
> >
> >
> >
> > I am trying to configure inverse-arp for ipv6 on a frame-relay
> circuit,
> > but pvc goes into unused state. Its only when I configure static map
> > commands pvc comes active.
> >
> > Configuration:
> >
> >
> >
> > Interface serial 1/7
> >
> > Ipv6 enable
> >
> > Ipv6 address 2001::/64 eui-64
> >
> > Encapsulation frame-relay
> >
> > Frame-relay inverse-arp ipv6 102
> >
> >
> >
> > On the same circuit if I am running ipv4 it works quite fine.
> >
> >
> >
> > Regards,
> >
> > Brajesh Thakur
> >
> >
> >
> >
> >
> >
> > The information contained in this electronic message and any
> attachments
> > to
> > this message are intended for the exclusive use of the addressee(s)
> and
> > may
> > contain proprietary, confidential or privileged information. If you
> are
> > not
> > the intended recipient, you should not disseminate, distribute or
copy
>
> > this
> > e-mail. Please notify the sender immediately and destroy all copies
of
>
> > this
> > message and any attachments.
> >
> > WARNING: Computer viruses can be transmitted via email. The
recipient
> > should
> > check this email and any attachments for the presence of viruses.
The
> > company
> > accepts no liability for any damage caused by any virus transmitted
by
>
> > this
> > email.
> >
> > www.wipro.com
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sat Aug 18 2007 - 08:17:39 ART