From: Gobind (gobind@inbox.com)
Date: Tue Mar 20 2007 - 16:25:43 ART
Hi,
I have just installed NM-2FE2w v2 in 3640 (C3640-IS-M), Version 12.4(12)
IOS,and it is now working and under "show diag" comamnd it is showing the
following :-
Router#sh diag
Slot 0:
NM-2FE2W_V2 Port adapter, 2 ports
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-21601-01
Board Revision : B0
Deviation Number : 0-0
Fab Version &nbs p; : 01
PCB Serial Number : FOC09014BBZ
RMA Test History : 00
RMA Number ; : 0-0-0-0
RMA History &nbs p; : 00
Product (FRU) Number : NM-2FE2W-V2=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 97 41 01 00 C0 46 03 20 00 54 61 01
0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 30
0x20: 39 30 31 34 42 42 5A 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 2:
NM-2FE2W Port adapter, 2 ports
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-04797-01
Board Revision : G0
Deviation Number : 0-0
Fab Version &nbs p; : 05
PCB Serial Number : JAD06250GBE
RMA Test History : 00
RMA Number ; : 0-0-0-0
RMA History &nbs p; : 00
Product (FRU) Number : NM-2FE2W=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 D8 41 01 00 C0 46 03 20 00 12 BD 01
0x10: 42 47 30 80 00 00 00 00 02 05 C1 8B 4A 41 44 30
0x20: 36 32 35 30 47 42 45 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Also the output of show version command :-
outer#sh ver
Cisco IOS Software, 3600 Software (C3640-IS-M), Version 12.4(12), RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport< BR>Copyright (c)
1986-2006 by Cisco Systems, Inc.
Compiled Fri 17-Nov-06 13:59 by prod_rel_team
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
Router uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:2.bin"
Cisco 3640 (R4700) processor (revision 0x00) with 124928K/6144K bytes of
memory.
Processor board ID 29400549
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
1 FastEthernet interface
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
It is showing up that is disabled,but this module is supported(NM2FE2W
v2) after 12.2(14) and above and I have installed 12.4,also tried 12.4
enterprise edition as IOS,but think the problem is something else
Kindly help me out!
Regards,
Gobind
This archive was generated by hypermail 2.1.4 : Sun Apr 01 2007 - 06:35:52 ART