From: Alexei Monastyrnyi (alexeim@orcsoftware.com)
Date: Wed Nov 15 2006 - 05:55:20 ART
that is because delay did not change.... there is not difference from
single src/dst flow view-point, it still goes through one interface.
A.
Victor Cappuccio wrote:
> Hmmm wondering why the DLY is not reduced as Bandwidth is added, this could help in EIGRP, since it uses the minimum bandwidth on the path to a destination network and the total delay to compute routing metrics
>
> GigabitEthernet1/2/0 is down, line protocol is down
> Hardware is GigabitEthernet, address is 0019.5585.e986 (bia 0019.5585.e986)
> Description: #### LinkCOLGATE-IP1COL01-12410 ####
> MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, rely 255/255, load 1/255
>
>
>
> Saludos,
> Victor.
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Alex De Gruiter
> Sent: Miircoles, 15 de Noviembre de 2006 12:29 a.m.
> To: Yoshe Rionando; ccielab@groupstudy.com
> Subject: RE: Etehrchannel
>
> show int port-channel [x]
>
> i.e.
>
> # show interface port-channel 1
>
> Port-channel1 is up, line protocol is up (connected)
> Hardware is EtherChannel, address is 0015.2b94.46ed (bia
> 0015.2b94.46ed)
> Description: Channel group connecting to switch 2
> MTU 1500 bytes, BW 4000000 Kbit, DLY 10 usec,
> <--------------------------
>
> # show etherchannel 1 summary
>
> Number of channel-groups in use: 4
> Number of aggregators: 4
>
> Group Port-channel Protocol Ports
> ------+-------------+-----------+---------------------------------------
> --------
> 1 Po1(SU) LACP Gi1/45(P) Gi1/46(P) Gi1/47(P)
> Gi1/48(P)
>
> Check out the bandwidth - the bonded interfaces will display bandwidth
> using the same manner as "regular" interfaces.
>
> Regards,
>
> Alex
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Yoshe Rionando
> Sent: Wednesday, 15 November 2006 2:59 PM
> To: ccielab@groupstudy.com
> Subject: Etehrchannel
>
> Hi Folks,
> How to verify speed of etherchannel. For example if i configure 3 port
> fastethernet to etherchannel, how can i verify that speed is 300 mbps?
>
>
> Yoshe Rionando Y.
> PT. Swadharma Duta Data
> Network & System Engineering Dept.
> Senior Network Engineer
> phone : 62 21 8318881
> fax : 62 21 8297293
> mobile : 62 8159084895
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> ******************************************************************************
> - NOTICE FROM DIMENSION DATA AUSTRALIA
> This message is confidential, and may contain proprietary or legally privileged information. If you have received this email in error, please notify the sender and delete it immediately.
>
> Internet communications are not secure. You should scan this message and any attachments for viruses. Under no circumstances do we accept liability for any loss or damage which may result from your receipt of this message or any attachments.
> ******************************************************************************
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:47 ART