From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Fri Sep 29 2006 - 13:58:46 ART
Russell,
Yes, for Cell Mode MPLS. The configuration is very short and
straightforward so it wouldn't warrant buying an LS1010 unless you
already have access to one.
HTH,
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: Russell Kelly (rukelly) [mailto:rukelly@cisco.com]
> Sent: Friday, September 29, 2006 11:34 AM
> To: Brian McGahan; Tony Schaffran; ccielab@groupstudy.com
> Subject: RE: ATM Topology Required For SP Lab
>
> Thanks Brian,
>
> - I used to see the back to back with the old R&S labs (well some of
> them) and was wondering if the SP (the new owner of ATM) called for
just
> this, or more - I assume for MPLS et al the new SP IE wkbk will call
for
> an ATM switch then? :-)
>
> Ta
> R
>
>
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> Sent: 29 September 2006 15:07
> To: Tony Schaffran; Russell Kelly (rukelly); ccielab@groupstudy.com
> Subject: RE: ATM Topology Required For SP Lab
>
> To run cell mode MPLS you need an MPLS aware ATM switch such as
> the LS1010. If you just want to do basic PVCs when you can run ATM
back
> to back.
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Tony Schaffran
> > Sent: Friday, September 29, 2006 8:42 AM
> > To: 'Russell Kelly (rukelly)'; ccielab@groupstudy.com
> > Subject: RE: ATM Topology Required For SP Lab
> >
> > You cannot configure any kind of SVC with a back-to-back ATM
> connection
> > between two routers.
> >
> > There is probably more you cannot do, but that one is pretty
> significant.
> >
> > Tony Schaffran
> > Network Analyst
> > CCIE #11071
> > CCNP, CCNA, CCDA,
> > NNCDS, NNCSS, CNE, MCSE
> >
> > www.cconlinelabs.com
> > Your #1 choice for online Cisco rack rentals.
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Russell Kelly (rukelly)
> > Sent: Friday, September 29, 2006 3:29 AM
> > To: ccielab@groupstudy.com
> > Subject: ATM Topology Required For SP Lab
> >
> >
> > Hi All,
> >
> > Just looking for some advice on the ATM topology required for the SP
> > workbooks (upcoming for ie) and the ipexpert SP workbook. It looks
> like
> > I cold get away with a back-to-back ATM connection without the need
> for
> > an LS1010 or the like. Is this the case - has someone set this up
> > recently who could help out?
> >
> > Cheers
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sun Oct 01 2006 - 16:55:41 ART