From: Ben (ccieben@cox.net)
Date: Fri May 05 2006 - 12:34:07 ART
Hi George,
What about "ipv6 ospf network point-to-point" on your R1 interface to
make it match the R2 side.
HTH
Ben
george stanza wrote:
> Thank you all for your pointers..
>
> On R1, i mapped the LINKLOCAL of R2's Serial and similary on R2, i mapped
> the LINKLOCAL of R1..Still no luck...Any idea what i am doing wrong here ?
>
> R1# sh ipv6 int s1 | inc FE80
> Serial1 is up, line protocol is up
> IPv6 is enabled, link-local address is FE80::209:11FF:FE60:A838
> R1(conf-if)# int s1
> R1(conf-if)# frame-relay map ipv6 FE80::209:11FF:FE60:A838 112 broadcast
>
> R2# sh ipv6 int s1 | inc FE80
> Serial1 is up, line protocol is up
> IPv6 is enabled, link-local address is FE80::250:73FF:FED2:3100
> R2(conf-if) int s1
> R2(conf-if) frame-relay map ipv6 FE80::209:11FF:FE60:A838 211 broadcast
>
>
>
>
>
>
>
>
>
>
>
>
> On 5/4/06, Zikopoulos Aristomenis <azik@altec.gr> wrote:
>
>> Hello George,
>> You can always find the link-local ipv6 address with
>> the show ipv6 inter serial 0/0 (example) command :
>>
>> Router#sh ipv6 inter se 0/0
>> Serial0/0 is administratively down, line protocol is down
>> IPv6 is enabled, link-local address is FE80::211:93FF:FE50:6040 [TEN]
>> Global unicast address(es):
>> 2001:CC1E::1, subnet is 2001:CC1E::/64 [TEN]
>> Joined group address(es):
>> FF02::1
>> FF02::1:FF00:1
>> FF02::1:FF50:6040
>> MTU is 1500 bytes
>> ICMP error messages limited to one every 100 milliseconds
>> ICMP redirects are enabled
>> ND DAD is enabled, number of DAD attempts: 1
>> ND reachable time is 30000 milliseconds
>>
>> The one with the FE80:: format.
>>
>> Regards,
>> Aris
>>
>>
>> -----Original Message-----
>> From: nobody@groupstudy.com on behalf of george stanza
>> Sent: Fri 5/5/2006 9:26 AM
>> To: Cisco certification
>> Subject: Ipv6 question !!
>>
>> R1 & R2 are connected over a frame-relay and i am trying to deploy ipv6
>> over
>> the FR circuit and configure OSPF between them..i dont see ipv6 OSPF
>> sessions coming up though..I believe i need to configure ipv6 link-local
>> address but the question says that the ipv6 address should be something
>> like
>> 2100:0108:122:15::1/64 & 2100:0108:122:15::2/64
>>
>> R1 Config:
>> ========
>> ipv6 unicast-routing
>> int s1
>> ipv6 address 2100:0108:122:15::1/64
>> ipv6 enable
>> ipv6 ospf 4 area 0
>> frame-relay map ipv6 2100:0108:122:15::2 112 broadcast
>>
>> R2 Config:
>> ========
>> ipv6 unicast-routing
>> int s1
>> ipv6 enable
>> ipv6 address 2100:0108:122:15::2/64
>> ipv6 ospf network point-to-point
>> ipv6 ospf 2 area 0
>> frame-relay map ipv6 2100:0108:122:15::1 121 broadcast
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:20 ART