From: Scott, Tyson C (tyson.scott@hp.com)
Date: Tue Mar 21 2006 - 11:45:53 GMT-3
There is nothing wrong with what you got. The NM-HDV2-1T1/E1 does not
come with any PVDM's by default. That is an add on.
http://www.cisco.com/en/US/products/hw/routers/ps282/products_data_sheet
09186a0080191d41.html
Look at table 4 on the information
It defines the PVDM's you need to order, You actually need to order the
PVDM2 series
Module Name
Description
Number of DSPs
Maximum Channels in High-Complexity1 Codec
Maximum Channels in Medium-Complexity2 Codec
Maximum Channels in G.711 codec
PVDM2-8
8-channel Packet Fax/Voice DSP Module
1
4
4
8
PVDM2-16
16-channel Packet Fax/Voice DSP Module
1
6
8
16
PVDM2-32
32-channel Packet Fax/Voice DSP Module
2
12
16
32
PVDM2-48
48-channel Packet Fax/Voice DSP Module
3
18
24
48
PVDM2-64
64-channel Packet Fax/Voice DSP Module
4
24
32
64
Regards,
Tyson Scott
Network Engineer
CCIE # 13513
-----Original Message-----
From: amir cohen [mailto:avi_patish@yahoo.com]
Sent: Tuesday, March 21, 2006 9:06 AM
To: Scott, Tyson C; Wolfgang Marschner; FORUM
Subject: RE: 2610XM voice card problem?
Guys,
I checked and found int the DIAG:
=============
Slot 0:
C2610XM 1FE Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 4.1
PCB Serial Number : FOC09423S17
Version Identifier :
Product (FRU) Number :
Chassis Serial Number : FTX1002C03G
Part Number : 73-7677-06
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : B0
Deviation Number : 0-0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 6A 41 04 01 C1 0B 46 4F 43 30 39
34
0x10: 32 33 53 31 37 89 FF FF FF FF CB 12 FF FF FF FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF C2 0B
0x30: 46 54 58 31 30 30 32 43 30 33 47 82 49 1D FD
06
0x40: 04 00 81 00 00 00 00 42 42 30 80 00 00 00 00 FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
Serial 2A/S (12in1)
Hardware revision 1.0 Board revision B0
Serial number 18219081 Part number
800-03182-01
FRU Part Number WIC-2A/S=
Test history 0x0 RMA number
00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 13 01 00 01 16 00 49 50 0C 6E 01 00 00 00 00
0x30: 58 00 00 00 00 01 20 00 FF FF FF FF FF FF FF FF
Slot 1:
High Density Voice NM-HDV2-1T1/E1 Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.1
Top Assy. Part Number : 800-22167-02
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC09504FMV
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Fab Part Number : 28-6126-04
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Product (FRU) Number : NM-HDV2-1T1/E1
Version Identifier : V02
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 DA 41 01 01 C0 46 03 20 00 56 97
02
0x10: 42 43 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 30
0x20: 39 35 30 34 46 4D 56 03 00 81 00 00 00 00 04 00
0x30: 85 1C 17 EE 04 C4 08 00 00 00 00 00 00 00 00
C5
0x40: 08 00 00 00 00 00 00 00 00 CB 8E 4E 4D 2D 48
44
0x50: 56 32 2D 31 54 31 2F 45 31 89 56 30 32 20 D9
02
0x60: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
FPGA revision:0x16C
WIC Slot 1:
HDV2 on board t1/e1 controller (1 port)
=============
THERE IS NO PVDM IN IT!!!
Is it a IOS issue, or the resseler sold me a voice card with no PVDM????
HELP NEEDED:-)
Amir
--- "Scott, Tyson C" <tyson.scott@hp.com> wrote:
> If all you have is a PVDM-12 you can only activate
> 12 channels,
> depending on the codec you are selecting it may even be less than 12.
> Test it. First make sure your router is recognizing the DSP
> resources.
> Then do the following.
>
> Config t
> Controller E1 1/0
> pri-group timeslots 1-6
>
> If that works then you know it is recognizing the PVDM's you have
> installed
>
> The maximum you are going to be able to do with only a PVDM 12 is 12
> channels if you are using a codec like G711
>
> Config t
> Controller E1 1/0
> pri-group timeslots 1-12
>
> Here is my test to show you
>
> (config-controller)#pri-group timeslots 1-31 % Not enough DSP
> resources available to configure pri-group on controller E1 0/0/1 %
> The remaining dsp resources are enough for 13 time slots.
> % For current codec complexity, 2 extra dsp(s) are required to create
> this voice port.
> (config-controller)#pri
> (config-controller)#pri-group ti
> (config-controller)#pri-group timeslots 1-5 Mar 21 08:46:23.670:
> %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(1),
> changed s tate to up
> Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(2),
> changed s tate to up
> Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(3),
> changed s tate to up
> Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(4),
> changed s tate to up
> Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(5),
> changed s tate to up
> Mar 21 08:46:24.634: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1 :0, changed state to down
> Mar 21 08:46:24.638: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1 :1, changed state to down
> Mar 21 08:46:24.638: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1 :2, changed state to down
> Mar 21 08:46:24.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1 :3, changed state to down
> Mar 21 08:46:24.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1 :4, changed state to down
> Mar 21 08:46:24.650: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0/1
>
>
> Regards,
>
> Tyson Scott
>
>
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of amir cohen
> Sent: Tuesday, March 21, 2006 8:34 AM
> To: Wolfgang Marschner; FORUM
> Subject: Re: 2610XM voice card problem?
>
> I am testing it oin a few minutes. will put the snapshot inside the
> MAIl.
>
> Meanwhile, below is the correct message that i getting form the
> routr:-) ===========================
>
>
>
> XXXXX(config)#dspfarm
> XXXXX(config)#^Z
> XXXXX#conf t
> Enter configuration commands, one per line. End with CNTL/Z.
> XXXXX(config)#conro
> XXXXX(config)#conrorole
> XXXXX(config)#conroroler e1 1/0
> ^
> % Invalid input detected at '^' marker.
>
> XXXXX(config)#controller e1 1/0
> XXXXX(config-controller)#pri-
> XXXXX(config-controller)#pri-group time
> XXXXX(config-controller)#pri-group timeslots 1/31
> ^ % Invalid input
> detected at '^' marker.
>
> XXXXX(config-controller)#pri-group timeslots 1-31 % Not enough DSP
> resources available to configure pri-group on controller E1 1/0 % The
> remaining dsp resources are enough for 0 time slots.
> % For current codec complexity, 2 extra dsp(s) are required to create
> this voice port.
> XXXXX(config-controller)#
>
>
> =========================
>
>
> Amir
>
> --- Wolfgang Marschner <wmarschner@web.de> wrote:
>
> > Amir,
> >
> > please have a look at your router with the
> commands I mentioned in
> > order to get a clue of what's going on. Then we
> can discuss it.
> > Here is a document which will help you testing
> your
> > NM-HDV:
> >
>
http://www.cisco.com/en/US/partner/tech/tk652/tk653/technologies_tech_no
> te09186a00800e66b1.shtml
> >
> > Regards
> >
> > Wolfgang
> > CSSI #23525, CCIE #8232
> >
> > ----- Original Message -----
> > From: "amir cohen" <avi_patish@yahoo.com>
> > To: "Wolfgang Marschner" <wmarschner@web.de>;
> "FORUM"
> > <ccielab@groupstudy.com>
> > Sent: Tuesday, March 21, 2006 1:49 PM
> > Subject: Re: 2610XM voice card problem?
> >
> >
> > > Wolfgang,
> > >
> > > This is a new card, and we bought it, along with
> > the
> > > PVDM,
> > >
> > > question:
> > >
> > > DO i have to activate the pvdm?
> > >
> > > Do i have to do something with the NM??
> > >
> > >
> > > Amir
> > > --- Wolfgang Marschner <wmarschner@web.de>
> wrote:
> > >
> > >> Simply not enough DSPs available.
> > >> Have a look with the command s"how diag",
> whether PVDM-12 modules
> > >> are installed on the
> > NM-HDV
> > >> and/or
> > >> check with the command "test dsp 1" your DSPs.
> > >> For your E1 you need at least 3 x PVDM-12!
> > >>
> > >> Regards
> > >>
> > >> Wolfgang
> > >> CSSI #23525, CCIE #8232
> > >>
> > >> ----- Original Message -----
> > >> From: "amir cohen" <avi_patish@yahoo.com>
> > >> To: "FORUM" <ccielab@groupstudy.com>
> > >> Sent: Tuesday, March 21, 2006 1:16 PM
> > >> Subject: 2610XM voice card problem?
> > >>
> > >>
> > >> > Guys,
> > >> >
> > >> >
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3