From: Scott, Tyson C (tyson.scott@hp.com)
Date: Tue Mar 21 2006 - 10:51:24 GMT-3
If all you have is a PVDM-12 you can only activate 12 channels,
depending on the codec you are selecting it may even be less than 12.
Test it. First make sure your router is recognizing the DSP resources.
Then do the following.
Config t
Controller E1 1/0
pri-group timeslots 1-6
If that works then you know it is recognizing the PVDM's you have
installed
The maximum you are going to be able to do with only a PVDM 12 is 12
channels if you are using a codec like G711
Config t
Controller E1 1/0
pri-group timeslots 1-12
Here is my test to show you
(config-controller)#pri-group timeslots 1-31
% Not enough DSP resources available to configure pri-group on
controller E1 0/0/1
% The remaining dsp resources are enough for 13 time slots.
% For current codec complexity, 2 extra dsp(s) are required to create
this voice port.
(config-controller)#pri
(config-controller)#pri-group ti
(config-controller)#pri-group timeslots 1-5
Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(1),
changed s tate to up
Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(2),
changed s tate to up
Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(3),
changed s tate to up
Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(4),
changed s tate to up
Mar 21 08:46:23.670: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/0/1:15(5),
changed s tate to up
Mar 21 08:46:24.634: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1 :0, changed state to down
Mar 21 08:46:24.638: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1 :1, changed state to down
Mar 21 08:46:24.638: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1 :2, changed state to down
Mar 21 08:46:24.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1 :3, changed state to down
Mar 21 08:46:24.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1 :4, changed state to down
Mar 21 08:46:24.650: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Serial0/0/1
Regards,
Tyson Scott
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
amir cohen
Sent: Tuesday, March 21, 2006 8:34 AM
To: Wolfgang Marschner; FORUM
Subject: Re: 2610XM voice card problem?
I am testing it oin a few minutes. will put the snapshot inside the
MAIl.
Meanwhile, below is the correct message that i getting form the routr:-)
===========================
XXXXX(config)#dspfarm
XXXXX(config)#^Z
XXXXX#conf t
Enter configuration commands, one per line. End with CNTL/Z.
XXXXX(config)#conro
XXXXX(config)#conrorole
XXXXX(config)#conroroler e1 1/0
^
% Invalid input detected at '^' marker.
XXXXX(config)#controller e1 1/0
XXXXX(config-controller)#pri-
XXXXX(config-controller)#pri-group time
XXXXX(config-controller)#pri-group timeslots 1/31
^ % Invalid input
detected at '^' marker.
XXXXX(config-controller)#pri-group timeslots 1-31 % Not enough DSP
resources available to configure pri-group on controller E1 1/0 % The
remaining dsp resources are enough for 0 time slots.
% For current codec complexity, 2 extra dsp(s) are required to create
this voice port.
XXXXX(config-controller)#
=========================
Amir
--- Wolfgang Marschner <wmarschner@web.de> wrote:
> Amir,
>
> please have a look at your router with the commands I mentioned in
> order to get a clue of what's going on. Then we can discuss it.
> Here is a document which will help you testing your
> NM-HDV:
>
http://www.cisco.com/en/US/partner/tech/tk652/tk653/technologies_tech_no
te09186a00800e66b1.shtml
>
> Regards
>
> Wolfgang
> CSSI #23525, CCIE #8232
>
> ----- Original Message -----
> From: "amir cohen" <avi_patish@yahoo.com>
> To: "Wolfgang Marschner" <wmarschner@web.de>; "FORUM"
> <ccielab@groupstudy.com>
> Sent: Tuesday, March 21, 2006 1:49 PM
> Subject: Re: 2610XM voice card problem?
>
>
> > Wolfgang,
> >
> > This is a new card, and we bought it, along with
> the
> > PVDM,
> >
> > question:
> >
> > DO i have to activate the pvdm?
> >
> > Do i have to do something with the NM??
> >
> >
> > Amir
> > --- Wolfgang Marschner <wmarschner@web.de> wrote:
> >
> >> Simply not enough DSPs available.
> >> Have a look with the command s"how diag", whether PVDM-12 modules
> >> are installed on the
> NM-HDV
> >> and/or
> >> check with the command "test dsp 1" your DSPs.
> >> For your E1 you need at least 3 x PVDM-12!
> >>
> >> Regards
> >>
> >> Wolfgang
> >> CSSI #23525, CCIE #8232
> >>
> >> ----- Original Message -----
> >> From: "amir cohen" <avi_patish@yahoo.com>
> >> To: "FORUM" <ccielab@groupstudy.com>
> >> Sent: Tuesday, March 21, 2006 1:16 PM
> >> Subject: 2610XM voice card problem?
> >>
> >>
> >> > Guys,
> >> >
> >> >
> >> > I have a 2610XM with NMHDV-1e1 ,
> >> > and when i am tryng to activate the command:
> >> >
> >> > Pri-group time-slot 1-31, i am getting
> >> >
> >> > " DSP Not enough DSP resources"
> >> > You have 0 DSP for time slots
> >> >
> >> >
> >> > here is the configuration:
> >> >
> >> >
> >> > =========================
> >> >
> >> > SHOW VER:
> >> > Yeruham#show controller e1
> >> > E1 1/0 is up.
> >> > Applique type is Channelized E1 - balanced No alarms detected.
> >> > alarm-trigger is not set
> >> > Version info Firmware: 20040802, FPGA: 255, spm_count = 0
> >> > Framing is CRC4, Line Code is HDB3, Clock
> Source
> >> is
> >> > Line.
> >> > Current port master clock:recovered from
> >> controller
> >> > 1/0
> >> > Data in current interval (138 seconds
> elapsed):
> >> > 0 Line Code Violations, 0 Path Code
> Violations
> >> > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err
> Secs,
> >> 0
> >> > Degraded Mins
> >> > 0 Errored Secs, 0 Bursty Err Secs, 0
> Severely
> >> Err
> >> > Secs, 0 Unavail Secs
> >> > Total Data (last 24 hours)
> >> > 257564 Line Code Violations, 5834 Path Code Violations,
> >> > 3 Slip Secs, 4 Fr Loss Secs, 12 Line Err
> Secs,
> >> 2
> >> > Degraded Mins,
> >> > 9 Errored Secs, 0 Bursty Err Secs, 5
> Severely
> >> Err
> >> > Secs, 84192 Unavail Secs
> >> > Yeruham#show ver
> >> > Cisco IOS Software, C2600 Software
> >> > (C2600-ADVENTERPRISEK9_IVS-M), Version 12.4(5
> >> > a), RELEASE SOFTWARE (fc3)
> >> > Technical Support:
> >> http://www.cisco.com/techsupport
> >> > Copyright (c) 1986-2006 by Cisco Systems, Inc.
> >> > Compiled Fri 13-Jan-06 19:19 by alnguyen
> >> >
> >> > ROM: System Bootstrap, Version 12.2(8r) [cmong
> >> 8r],
> >> > RELEASE SOFTWARE (fc1)
> >> >
> >> > Yeruham uptime is 1 week, 5 days, 16 hours, 3
> >> minutes
> >> > System returned to ROM by reload
> >> > System image file is
> >> > "flash:c2600-adventerprisek9_ivs-mz.124-5a.bin"
> >> >
> >> >
> >> > This product contains cryptographic features
> and
> >> is
> >> > subject to United
> >> > States and local country laws governing import,
> >> > export, transfer and
> >> > use. Delivery of Cisco cryptographic products
> does
> >> not
> >> > imply
> >> > third-party authority to import, export,
> >> distribute or
> >> > use encryption.
> >> > Importers, exporters, distributors and users
> are
> >> > responsible for
> >> > compliance with U.S. and local country laws. By
> >> using
> >> > this product you
> >> > agree to comply with applicable laws and
> >> regulations.
> >> > If you are unable
> >> > to comply with U.S. and local laws, return this
> >> > product immediately.
> >> >
> >> > A summary of U.S. laws governing Cisco
> >> cryptographic
> >> > products may be found at:
> >> >
> >>
> >
>
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
> >> >
> >> > If you require further assistance please
> contact
> >> us by
> >> > sending email to
> >> > export@cisco.com.
> >> >
> >> > Cisco 2610XM (MPC860P) processor (revision 4.1)
> >> with
> >> > 124005K/7067K bytes of memo
> >> > ry.
> >> > Processor board ID FTX1002C03G
> >> > M860 processor: part number 5, mask 2
> >> > 1 FastEthernet interface
> >> > 2 Low-speed serial(sync/async) interfaces
> >> > 1 Channelized E1/PRI port
> >> > 32K bytes of NVRAM.
> >> > 32768K bytes of processor board System flash
> >> > (Read/Write)
> >> >
> >> > ========================================
> >> >
> >> > Configuration:
> >> >
> >> >
> >> > ===============
> >> > Current configuration : 1464 bytes
> >> > !
> >> > version 12.4
> >> > service timestamps debug datetime msec
> >> > service timestamps log datetime msec
> >> > no service password-encryption
> >> > !
> >> > hostname XXXX
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3