From: amir cohen (avi_patish@yahoo.com)
Date: Tue Mar 21 2006 - 10:34:24 GMT-3
I am testing it oin a few minutes. will put the
snapshot inside the MAIl.
Meanwhile, below is the correct message that i getting
form the routr:-)
===========================
XXXXX(config)#dspfarm
XXXXX(config)#^Z
XXXXX#conf t
Enter configuration commands, one per line. End with
CNTL/Z.
XXXXX(config)#conro
XXXXX(config)#conrorole
XXXXX(config)#conroroler e1 1/0
^
% Invalid input detected at '^' marker.
XXXXX(config)#controller e1 1/0
XXXXX(config-controller)#pri-
XXXXX(config-controller)#pri-group time
XXXXX(config-controller)#pri-group timeslots 1/31
^
% Invalid input detected at '^' marker.
XXXXX(config-controller)#pri-group timeslots 1-31
% Not enough DSP resources available to configure
pri-group on controller E1 1/0
% The remaining dsp resources are enough for 0 time
slots.
% For current codec complexity, 2 extra dsp(s) are
required to create this voice
port.
XXXXX(config-controller)#
=========================
Amir
--- Wolfgang Marschner <wmarschner@web.de> wrote:
> Amir,
>
> please have a look at your router with the commands
> I mentioned in order to
> get
> a clue of what's going on. Then we can discuss it.
> Here is a document which will help you testing your
> NM-HDV:
>
http://www.cisco.com/en/US/partner/tech/tk652/tk653/technologies_tech_note09186a00800e66b1.shtml
>
> Regards
>
> Wolfgang
> CSSI #23525, CCIE #8232
>
> ----- Original Message -----
> From: "amir cohen" <avi_patish@yahoo.com>
> To: "Wolfgang Marschner" <wmarschner@web.de>;
> "FORUM"
> <ccielab@groupstudy.com>
> Sent: Tuesday, March 21, 2006 1:49 PM
> Subject: Re: 2610XM voice card problem?
>
>
> > Wolfgang,
> >
> > This is a new card, and we bought it, along with
> the
> > PVDM,
> >
> > question:
> >
> > DO i have to activate the pvdm?
> >
> > Do i have to do something with the NM??
> >
> >
> > Amir
> > --- Wolfgang Marschner <wmarschner@web.de> wrote:
> >
> >> Simply not enough DSPs available.
> >> Have a look with the command s"how diag",
> >> whether PVDM-12 modules are installed on the
> NM-HDV
> >> and/or
> >> check with the command "test dsp 1" your DSPs.
> >> For your E1 you need at least 3 x PVDM-12!
> >>
> >> Regards
> >>
> >> Wolfgang
> >> CSSI #23525, CCIE #8232
> >>
> >> ----- Original Message -----
> >> From: "amir cohen" <avi_patish@yahoo.com>
> >> To: "FORUM" <ccielab@groupstudy.com>
> >> Sent: Tuesday, March 21, 2006 1:16 PM
> >> Subject: 2610XM voice card problem?
> >>
> >>
> >> > Guys,
> >> >
> >> >
> >> > I have a 2610XM with NMHDV-1e1 ,
> >> > and when i am tryng to activate the command:
> >> >
> >> > Pri-group time-slot 1-31, i am getting
> >> >
> >> > " DSP Not enough DSP resources"
> >> > You have 0 DSP for time slots
> >> >
> >> >
> >> > here is the configuration:
> >> >
> >> >
> >> > =========================
> >> >
> >> > SHOW VER:
> >> > Yeruham#show controller e1
> >> > E1 1/0 is up.
> >> > Applique type is Channelized E1 - balanced
> >> > No alarms detected.
> >> > alarm-trigger is not set
> >> > Version info Firmware: 20040802, FPGA: 255,
> >> > spm_count = 0
> >> > Framing is CRC4, Line Code is HDB3, Clock
> Source
> >> is
> >> > Line.
> >> > Current port master clock:recovered from
> >> controller
> >> > 1/0
> >> > Data in current interval (138 seconds
> elapsed):
> >> > 0 Line Code Violations, 0 Path Code
> Violations
> >> > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err
> Secs,
> >> 0
> >> > Degraded Mins
> >> > 0 Errored Secs, 0 Bursty Err Secs, 0
> Severely
> >> Err
> >> > Secs, 0 Unavail Secs
> >> > Total Data (last 24 hours)
> >> > 257564 Line Code Violations, 5834 Path Code
> >> > Violations,
> >> > 3 Slip Secs, 4 Fr Loss Secs, 12 Line Err
> Secs,
> >> 2
> >> > Degraded Mins,
> >> > 9 Errored Secs, 0 Bursty Err Secs, 5
> Severely
> >> Err
> >> > Secs, 84192 Unavail Secs
> >> > Yeruham#show ver
> >> > Cisco IOS Software, C2600 Software
> >> > (C2600-ADVENTERPRISEK9_IVS-M), Version 12.4(5
> >> > a), RELEASE SOFTWARE (fc3)
> >> > Technical Support:
> >> http://www.cisco.com/techsupport
> >> > Copyright (c) 1986-2006 by Cisco Systems, Inc.
> >> > Compiled Fri 13-Jan-06 19:19 by alnguyen
> >> >
> >> > ROM: System Bootstrap, Version 12.2(8r) [cmong
> >> 8r],
> >> > RELEASE SOFTWARE (fc1)
> >> >
> >> > Yeruham uptime is 1 week, 5 days, 16 hours, 3
> >> minutes
> >> > System returned to ROM by reload
> >> > System image file is
> >> > "flash:c2600-adventerprisek9_ivs-mz.124-5a.bin"
> >> >
> >> >
> >> > This product contains cryptographic features
> and
> >> is
> >> > subject to United
> >> > States and local country laws governing import,
> >> > export, transfer and
> >> > use. Delivery of Cisco cryptographic products
> does
> >> not
> >> > imply
> >> > third-party authority to import, export,
> >> distribute or
> >> > use encryption.
> >> > Importers, exporters, distributors and users
> are
> >> > responsible for
> >> > compliance with U.S. and local country laws. By
> >> using
> >> > this product you
> >> > agree to comply with applicable laws and
> >> regulations.
> >> > If you are unable
> >> > to comply with U.S. and local laws, return this
> >> > product immediately.
> >> >
> >> > A summary of U.S. laws governing Cisco
> >> cryptographic
> >> > products may be found at:
> >> >
> >>
> >
>
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
> >> >
> >> > If you require further assistance please
> contact
> >> us by
> >> > sending email to
> >> > export@cisco.com.
> >> >
> >> > Cisco 2610XM (MPC860P) processor (revision 4.1)
> >> with
> >> > 124005K/7067K bytes of memo
> >> > ry.
> >> > Processor board ID FTX1002C03G
> >> > M860 processor: part number 5, mask 2
> >> > 1 FastEthernet interface
> >> > 2 Low-speed serial(sync/async) interfaces
> >> > 1 Channelized E1/PRI port
> >> > 32K bytes of NVRAM.
> >> > 32768K bytes of processor board System flash
> >> > (Read/Write)
> >> >
> >> > ========================================
> >> >
> >> > Configuration:
> >> >
> >> >
> >> > ===============
> >> > Current configuration : 1464 bytes
> >> > !
> >> > version 12.4
> >> > service timestamps debug datetime msec
> >> > service timestamps log datetime msec
> >> > no service password-encryption
> >> > !
> >> > hostname XXXX
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3