From: Ivan (ivan@iip.net)
Date: Thu Mar 16 2006 - 08:04:44 GMT-3
R4
int Virtual-Template1
missed ppp multilink. Is it typo error ?
> Hi,
> here is the config
>
> it is between r3,r4 adn r5
> R3
>
> interface Multilink1
> ip address 145.1.0.3 255.255.255.0
> ppp multilink
> ppp multilink group 1
> !
> interface Multilink2
> ip address 145.1.0.3 255.255.255.0
> ppp multilink
> ppp multilink group 2
> interface Serial1/0.304 point-to-point
> frame-relay interface-dlci 304 ppp Virtual-Template2
> !
> interface Serial1/0.305 point-to-point
> frame-relay interface-dlci 305 ppp Virtual-Template1
> !
>
>
> interface Virtual-Template1
> no ip address
> ppp multilink
> ppp multilink group 1
> !
> interface Virtual-Template2
> no ip address
> ppp multilink
> ppp multilink group 2
>
>
>
> router R4
>
>
> interface Multilink1
> ip address 145.1.0.4 255.255.255.0
> ppp multilink
> ppp multilink group 1
> !
> interface Multilink2
> ip address 145.1.0.4 255.255.255.0
> ppp multilink
> ppp multilink group 2
> !
> interface Ethernet0/0
> ip address 145.1.47.4 255.255.255.0
> half-duplex
> !
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> !
> interface Serial0/0.403 point-to-point
> frame-relay interface-dlci 403 ppp Virtual-Template1
> !
> interface Serial0/0.413 point-to-point
> frame-relay interface-dlci 413 ppp Virtual-Template2
> !
> interface Ethernet0/1
> no ip address
> shutdown
> half-duplex
> !
> interface Serial0/1
> no ip address
> encapsulation frame-relay
> no keepalive
> !
> interface Virtual-Template1
> no ip address
> ppp multilink group 1
> !
> interface Virtual-Template2
> no ip address
> ppp multilink
> ppp multilink group 2
> !
>
>
> R5
>
>
> interface Multilink1
> ip address 145.1.0.5 255.255.255.0
> ppp multilink
> ppp multilink group 1
> !
> interface Multilink2
> ip address 145.1.0.5 255.255.255.0
> ppp multilink
> ppp multilink group 2
> !
>
> interface Serial0/0
> no ip address
> encapsulation frame-relay
> !
> interface Serial0/0.503 point-to-point
> frame-relay interface-dlci 503 ppp Virtual-Template1
> !
> interface Serial0/0.513 point-to-point
> frame-relay interface-dlci 513 ppp Virtual-Template2
>
> interface Virtual-Template1
> no ip address
> ppp multilink
> ppp multilink group 1
> !
> interface Virtual-Template2
> no ip address
> ppp multilink
> ppp multilink group 2
>
>
>
>
> _ venkatesh
>
> On 3/16/06, Alexei Monastyrnyi <alexeim@orcsoftware.com> wrote:
> > could you post an exact configuration please?
> >
> > on 16/03/2006 10:10 Venkatesh Palani wrote:
> > > Hi All,
> > > I have some issues getting around configuring multilink over PPPoFR. Is
> > > traffic shaping configuration a required one when we configure
> > > Multilink PPPoFR ?
> > > because I get the following message
> > >
> > > Apr 9 12:51:45.315: %FR-3-MLPOFR_ERROR: MLPoFR not configured properly
> >
> > on
> >
> > > Link Virtual-Access3 Bundle Multilink2 :Frame Relay traffic shaping
> > > must
> >
> > be
> >
> > > enabled
> > > *Apr 9 12:51:45.851: %FR-3-MLPOFR_ERROR: MLPoFR not configured
> > > properly
> >
> > on
> >
> > > Link Virtual-Access4 Bundle Multilink1 :Frame Relay traffic shaping
> > > must
> >
> > be
> >
> > > enabled
> > >
> > > I have 2 multilink interafces 1 and 2
> > > and two virtual-templates 1 and 2
> > > as you woudl have guessed 1 matches to 1 and 2 matches to 2
> > >
> > > The cisco documnet shows an example that has a QOS as part of the
> > > configuration. coudl any oen shed more light on to this please ?
> > >
> > > Thank you,
> > > venkatesh
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
-- Ivan
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3