From: san (san.study@gmail.com)
Date: Sat Jun 04 2005 - 21:58:02 GMT-3
Yes,
i had only the related concept in mind to look for this
command....then after reading understood this is default behaviour &
use this command to look for watched route in initial bootup time.
Thanks
SAN
On 6/4/05, Sean C <Upp_and_Upp@hotmail.com> wrote:
> Hi San,
>
> Ahh, ok, the exact opposite. The original task "not to initiate the dialer
> watch process untill all the routing protocols settle down after the router
> boot up" isn't solved by using 'delay route-check initial time'.
> Per the CD: The Dialer Watch feature is triggered only when the primary
> route is removed from the routing table. If the primary link fails to come
> up during initial startup of the router, the route is never added to the
> routing table and will not be watched.
> So, for this task, the, using 'delay route-check' won't solve the issue. In
> fact, nothing is needed since it's the default.
>
> But if the task wanted the router's dialer watch to initiate a call even at
> the initial boot-up if the route isn't in the route-table, then you would
> use 'delay route-check initial time' syntax.
>
> Hope this makes sense,
> Sean
> ----- Original Message -----
> From: "san" <san.study@gmail.com>
> To: "Sean C" <Upp_and_Upp@hotmail.com>
> Cc: "GroupStudy" <ccielab@groupstudy.com>
> Sent: Saturday, June 04, 2005 8:16 PM
> Subject: Re: trying to recollect dialer watch command
>
>
> > After 1.5 hrs of search for 1 cmd....Here is the valuable cmd.
> >
> > dialer watch-list group-number {ip ip-address address-mask | delay
> > route-check initial time}
> >
> > /SAN
> >
> >
> > On 6/4/05, Sean C <Upp_and_Upp@hotmail.com> wrote:
> >> Hi San,
> >>
> >> According to the 12.3 Master-command list, there's only 4 dialer watch
> >> commands, so you think it would have to be one of the 4.
> >>
> >> I would think 'dialer watch-list delay' but this doesn't wait for any
> >> routing-protocol to be 'synched' before being enabled like you are
> >> looking
> >> for. I thought I remember a similar question from one of the IEWBs
> >> (perhaps
> >> the new Volume 2?) but I thought it just asked to wait some set of time,
> >> not
> >> specifically for the routing protocol(s) to be synched.
> >>
> >> Sean
> >> > ----- Original Message -----
> >> > From: "san" <san.study@gmail.com>
> >> > To: "Group Study" <ccielab@groupstudy.com>
> >> > Sent: Saturday, June 04, 2005 7:25 PM
> >> > Subject: trying to recollect dialer watch command
> >> >
> >> >
> >> >> Hi ,
> >> >>
> >> >> I am trying to recollect a command that is used for "not to initiate
> >> >> the dialer watch process untill all the routing protocols settle down
> >> >> after the router boot up".
> >> >>
> >> >> This command is to make sure, that watched route already exists in
> >> >> routing table, before looking for non-exists of same routes.
> >> >>
> >> >> I tried looking in Doc, but could not get it my searches.
> >> >>
> >> >> If anyone remembers, help me.
> >> >>
> >> >> /SAN
> >> >>
> >> >> _______________________________________________________________________
> >> >> Subscription information may be found at:
> >> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:40 GMT-3