From: san (san.study@gmail.com)
Date: Sat May 14 2005 - 02:36:30 GMT-3
Thanks Loc,
After making sure my configurations are correct from the link, i
reloaded & everything is ok.
Is ther order of creating interfaces & assocations that i need to follow ?
Below are the correct configs:
interface BRI0/0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-5ess
ppp multilink
!
interface Ethernet0/1
ip address 191.1.48.4 255.255.255.0
half-duplex
!
interface Dialer1
ip address 191.1.45.4 255.255.255.0
encapsulation ppp
dialer pool 1
dialer idle-timeout 120 either
dialer string 60002
dialer watch-group 1
ppp multilink
ppp multilink links minimum 2
!
router eigrp 10
network 191.1.4.4 0.0.0.0
--More--
*Mar 1 00:07:02.179: Di1 DDR: idle timeout
*Mar 1 00:07:02.179: DDR: Dialer Watch: watch-group = 1
*Mar 1 00:07:02.179: DDR: network 150.1.6.0/255.255.255.0 UP,
*Mar 1 00:07:02.179: DDR: primary DOWN
/access-list
filtering...
access-list 145 permit icmp host 191.1.45.4 host 191.1.45.5
dialer watch-list 1 ip 150.1.6.0 255.255.255.0
dialer watch-list 1 delay disconnect 300
dialer-list 1 protocol ip list 145
/SAN
On 5/12/05, Loc Pham <loc.pham@comcast.net> wrote:
> Hello San , James,
> I done IEWB lab (# 3? ) recently and your # 1 seem to functional otherwise:
> http://www.cisco.com/warp/public/129/bri-backup-map-watch.html
> So I think the " dialer idle-timeout " will not disconnect your ISDN in this case. I can not test it at that time ( have a 12.2 on 2503 ) since the " dialer watch-list disconnect " is not available .
> May be someone can run & validate with debug ppp packet.
> lP.
>
>
> > Good Spot -
> >
> > I think both, otherwise you are not waiting long enough
> >
> > So if delay disconnect > current idle timeout
> >
> > then you need to alter the idle timeout.
> >
> > -----Original Message-----
> > From: san [mailto:san.study@gmail.com]
> > Sent: 12 May 2005 04:02
> > To: Cisco certification
> > Subject: Dialer watch scenario
> >
> >
> > Task:
> > ISDN circuit should only be disconnected after the FR circuite comes
> > back up and has been stable for 5 minutes ?
> >
> >
> > Probable Answer:
> >
> > 1. "dialer idle time 300"
> >
> > 2. dialer watch-list 1 delay disconnect 300
> >
> >
> > Results:
> >
> > If i use only dialer watch-list disconnect 300, ISDN is disconnected
> > by default idle timer 120 seconds. Is this accepted ? or should i use
> > both combination ?
> >
> >
> > /SAN
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > **********************************************************************
> > *********** Department of Agriculture and Food ***************
> >
> > The information contained in this email and in any
> > attachments is confidential and is designated solely
> > for the attention and use of the intended recipient(s).
> > This information may be subject to legal and professional
> > privilege. If you are not an intended recipient of
> > this email, you must not use, disclose, copy,
> > distribute or retain this message or any part of it.
> > If you have received this email in error, please
> > notify the sender immediately and delete all copies of
> > this email from your computer system(s).
> > **********************************************************************
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:11:58 GMT-3