From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Tue Feb 01 2005 - 18:46:03 GMT-3
Mesut,
Did you *define* the VLAN as an rspan vlan?
Rack1SW1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1SW1(config)#vlan 100
Rack1SW1(config-vlan)#remote-span
Rack1SW1(config-vlan)#end
Rack1SW1#
01:52:41: %SYS-5-CONFIG_I: Configured from console by console
Rack1SW1#show vlan | begin Remote
Remote SPAN VLANs
------------------------------------------------------------------------
------
100
Primary Secondary Type Ports
------- --------- -----------------
------------------------------------------
Rack1SW1#
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: Mesut Abdurrahmani [mailto:mesut@kujtesa.com]
> Sent: Tuesday, February 01, 2005 3:43 PM
> To: Brian McGahan
> Cc: ccielab@groupstudy.com
> Subject: RE: Remote SPAN Question
>
> Brian,
>
> Thanks for you quick response. I've configured reflector-port on a
port
> that
> is not active, switch gives the green light on that port ( I think it
is
> looped) but still can't sniff the information on Switch A ( source
> switch).
> Other configuration is the same except the reflector-port. Is there
any
> possibility of a bug on catalyst 2950 switches?
>
> Thanks
> Best regards
> Mesut Abdurrahmani
>
>
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> Sent: Tuesday, February 01, 2005 9:52 PM
> To: Mesut Abdurrahmani; ccielab@groupstudy.com
> Subject: RE: Remote SPAN Question
>
> Mesut,
>
> The reflector port should not be an active interface. In order
> to run RSPAN you must dedicate one interface to be the reflector port.
> Change it to something else besides fa0/5 and it should work.
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Mesut Abdurrahmani
> > Sent: Tuesday, February 01, 2005 2:23 PM
> > To: ccielab@groupstudy.com
> > Subject: Remote SPAN Question
> >
> > Hi
> >
> >
> >
> > I'm trying to implement Remote SPAN feature on my 2 x 2950 but
wasn't
> > successful till now. I have created a Remote Span Vlan on both
> switches
> > (VLAN 6), switches are interconnected through a trunk (Fa0/5). On
> source
> > switch I've used the following commands
> >
> >
> >
> > Monitor session 1 source interface fa0/6 - 24 tx
> >
> > Monitor session 1 destination remote vlan 6 reflector-port fa0/5
> >
> >
> >
> > And on destination switch
> >
> >
> >
> > Monitor session 1 source remote vlan 6
> >
> > Monitor session 1 destination interface fa0/24
> >
> >
> >
> > There are no access ports that use vlan 6 (RSPAN VLAN )as it meant
to
> be
> > and
> > all I've disabled Pruning on Vlan 6.
> >
> >
> >
> > The Reflector-port (fa0/5) on switch A and destination interface on
> Switch
> > B
> > (fa0/24) goes on monitoring state, which is OK
> >
> > FastEthernet0/24 is down, line protocol is down (monitoring)
> >
> >
> >
> > Hope to get help
> >
> >
> >
> > Thanks in Advance,
> >
> > Regards,
> >
> > Mesut Abdurrahmani
> >
> >
>
This archive was generated by hypermail 2.1.4 : Thu Mar 03 2005 - 08:51:15 GMT-3