From: joshua lauer (jslauer@hotmail.com)
Date: Mon Sep 06 2004 - 18:32:03 GMT-3
is your demarc extended? does your demarc terminate at one point or do you
have it extended from the actual termination point to somewhere else in the
area? I.E. is your CSU/DSU somewhere other than where the actual line comes
in, could be physical problems from the actual line of demarcation to where
the CSU/DSU is located, Just a shot in the dark here from the info you
provided.
jl
jl
Josh Lauer
----- Original Message -----
From: "ccie2be" <ccie2be@nyc.rr.com>
To: "jb" <barrerj1@hotmail.com>; "steve martin" <w2kask@yahoo.com>
Cc: <ccielab@groupstudy.com>
Sent: Monday, September 06, 2004 4:37 PM
Subject: Re: serial0 interface is up, line protocol is down-NEW LINE
[7:92538]
> Hi,
>
> What does "Extended DMARC: Yes or NO" refer to?
>
> Thanks
>
> ----- Original Message -----
> From: "jb" <barrerj1@hotmail.com>
> To: "steve martin" <w2kask@yahoo.com>
> Cc: <ccielab@groupstudy.com>
> Sent: Monday, September 06, 2004 1:11 PM
> Subject: Re: serial0 interface is up, line protocol is down-NEW LINE
> [7:92538]
>
>
>> Steve,
>>
>> We need to know more thant that?
>>
>> Connectiong type: P2P or frame?
>> Router Type:
>> Cisco IOS:
>> Interface type: Serial V.35 or WIC-Card
>> Extended DMARC: Yes or NO
>> Do you see any alarms:?
>> Can you see Carrier detect in case of WIC-T1?
>>
>> JB
>>
>>
>>
>>
>> ----- Original Message -----
>> From: "steve martin" <w2kask@yahoo.com>
>> To: <cisco@groupstudy.com>
>> Sent: Monday, September 06, 2004 9:19 AM
>> Subject: serial0 interface is up, line protocol is down-NEW LINE
>> [7:92538]
>>
>>
>>> Hi.. We just order a new line from a new ISP,
>>> it give us a customer IP as IP as 100.100.100.174
>>> /255.255.255.252 and ISP End IP as 100.100.100.173
>>> /255.255.255.252. And it gives us a Public IP range
>>> of 101.101.101.160/255.255.255.224. So I configured
>>> serial IP as 100.100.100.174 and default gateway as ip
>>> route 0.0.0.0 0.0.0.0 100.100.100.173 and I configured
>>> the following 101.101.101.170 as the common public IP
>>> as below. BUTTTTT.. After I connect the new line to
>>> the serial0, it gives me this error, serial0 interface
>>> is up, line protocol is down. I Unplug and RE-plug
>>> the modem cable, the line protocol change state to UP
>>> a short while when I replug , BUT quickly down again.
>>> What's wrong?? I called my ISP hotline but no answer
>>> so I seek your opinion here
>>>
>>> ip nat pool Internet_E11 101.101.101.170
>>> 101.101.101.170 netmask 255.255.255.224
>>> ip nat inside source route-map imap pool Internet_E11
>>> overload
>>> access-list 107 permit ip 192.168.6.0 0.0.0.255 any
>>> route-map imap permit 10
>>> match ip address 107
>>> !
>>>
>>>
>>>
>>>
>>> __________________________________
>>> Do you Yahoo!?
>>> New and Improved Yahoo! Mail - 100MB free storage!
>>> http://promotions.yahoo.com/new_mail
>>
>> _______________________________________________________________________
>> Please help support GroupStudy by purchasing your study materials from:
>> http://shop.groupstudy.com
>>
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Oct 01 2004 - 15:00:38 GMT-3