Fw: RSVP FOR VOICE TRAFFIC!!

From: Sergio Jimenez Arguedas (sejimenez@its.co.cr)
Date: Fri May 21 2004 - 23:41:47 GMT-3


RE: RSVP FOR VOICE TRAFFIC!!Hi Richard!!!

Umm, The default codec it has is:

R3#sh dial-peer voice | i codec
        codec = g729r8, payload size = 20 bytes,
        codec = g729r8, payload size = 20 bytes,

So, It uses 24K

I also changed the controlled-load option, but It didn4t work!!!

dial-peer voice 3 voip
 destination-pattern 5302
 session target ipv4:129.44.85.1
 req-qos
 acc-qos controlled-load

Rgds,

Sergio

----- Original Message -----
From: Richard Dumoulin
To: Sergio Jimenez Arguedas
Sent: Friday, May 21, 2004 7:50 PM
Subject: RE: RSVP FOR VOICE TRAFFIC!!

Please, tell us how it goes, I'm interested :)

-----Original Message-----
From: Richard Dumoulin
Sent: sabado, 22 de mayo de 2004 3:19
To: Sergio Jimenez Arguedas; ccielab@groupstudy.com
Subject: RE: RSVP FOR VOICE TRAFFIC!!

I'll give it a try. The default codec is G729ar8 which needs something like 30
Kbps aprox without CRTP. So maybe your 24Kbps reservation with RSVP is not
enough ? Can you try "ip rsvp bandwidth 40 40" or "req-qos controlled-load"
instead ?

"debug ip rsvp" might be useful,

--Richard

-----Original Message-----
From: Sergio Jimenez Arguedas [mailto:sejimenez@its.co.cr]
Sent: sabado, 22 de mayo de 2004 3:10
To: ccielab@groupstudy.com
Subject: RSVP FOR VOICE TRAFFIC!!

Hi Group!!!

I have a problem with a VoIP Scenario using RSVP:

TEL-----------R1-e0/0-----------------------------------e0/0-R2-------------
-
--TEL

R1_Config

interface Ethernet0/0
 ip address 129.44.85.1 255.255.255.0
 half-duplex
 fair-queue 64 256 1
 ip rsvp bandwidth 24 24
!
dial-peer voice 2 pots
 destination-pattern 5302
 port 3/0/1
!
dial-peer voice 3 voip
 destination-pattern 5000
 session target ipv4:129.44.85.5
 req-qos guaranteed-delay
 acc-qos guaranteed-delay

R2_Config

interface Ethernet0/0
 ip address 129.44.85.5 255.255.255.0
 half-duplex
 fair-queue 64 256 1
 ip rsvp bandwidth 24 24
!
dial-peer voice 1 pots
 destination-pattern 5000
 port 1/0/0
!
dial-peer voice 3 voip
 destination-pattern 5302
 session target ipv4:129.44.85.1
 req-qos guaranteed-delay
 acc-qos guaranteed-delay

Without the RSVP config, I don4t have problems!!!

But, with RSVP I got it:

R2#csim start 5302
csim: called number = 5302, loop count = 1 ping count = 0

csim err csimDisconnected recvd DISC cid(55)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0

Can somebody help me, please?

Just tell me if you some show or debug cmd!!!

Rgds,

Sergio



This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:15 GMT-3