From: john matus (jmatus@pacbell.net)
Date: Mon Mar 15 2004 - 21:17:23 GMT-3
what do you have to do too get 2 bgp peer that are stuck in active/idle w/
an up/down of never to connect (under 'sh ip b sum')?
i cant figure this out!....or what is it indicative of?
Regards,
John D. Matus
MCSE, CCNP
818.782.2061 office
818.430.8372 mobile
jmatus@pacbell.net
----- Original Message -----
From: "Sergio Jimenez Arguedas" <sejimenez@its.co.cr>
To: <ccielab@groupstudy.com>
Sent: Monday, March 15, 2004 2:41 PM
Subject: Fw: REDISTRIBUTE IN OSPF
> Sure,
>
>
> R3_sh run
>
>
> !
> interface Loopback0
> ip address 130.10.31.1 255.255.255.224
> !
> interface Loopback1
> ip address 130.10.31.33 255.255.255.224
> !
> interface Loopback33
> ip address 33.33.33.3 255.255.255.0
> !
> interface Ethernet0/0
> ip address 130.10.30.3 255.255.255.0
> half-duplex
> !
> interface TokenRing0/0
> no ip address
> shutdown
> ring-speed 16
> !
> interface Serial1/0
> bandwidth 128
> ip address 130.10.134.3 255.255.255.0
> encapsulation frame-relay
> ip ospf priority 0
> no arp frame-relay
> frame-relay map ip 130.10.134.1 100 broadcast
> frame-relay map ip 130.10.134.4 100 broadcast
> no frame-relay inverse-arp
> frame-relay lmi-type ansi
> !
> interface Serial1/1
> no ip address
> shutdown
> !
> interface Serial1/2
> no ip address
> shutdown
> !
> interface Serial1/3
> no ip address
> shutdown
> !
> router ospf 1
> log-adjacency-changes
> redistribute connected metric 10 subnets
> network 130.10.30.0 0.0.0.255 area 3
> network 130.10.134.0 0.0.0.255 area 0
> !
>
>
> R4_sh run
>
>
> !
> !
> interface Loopback0
> ip address 130.10.41.1 255.255.255.252
> !
> interface Loopback1
> ip address 130.10.41.5 255.255.255.252
> !
> interface Ethernet0/0
> ip address 130.10.40.4 255.255.255.0
> half-duplex
> !
> interface TokenRing0/0
> no ip address
> shutdown
> ring-speed 16
> !
> interface Serial1/0
> bandwidth 128
> ip address 130.10.134.4 255.255.255.0
> encapsulation frame-relay
> ip ospf network non-broadcast
> ip ospf priority 0
> no arp frame-relay
> frame-relay map ip 130.10.134.1 110 broadcast
> frame-relay map ip 130.10.134.3 110 broadcast
> no frame-relay inverse-arp
> frame-relay lmi-type ansi
> !
> interface Serial1/1
> no ip address
> shutdown
> !
> interface Serial1/2
> no ip address
> shutdown
> !
> interface Serial1/3
> no ip address
> shutdown
> !
> router ospf 1
> log-adjacency-changes
> summary-address 130.10.41.0 255.255.255.0
> redistribute connected metric 5 subnets route-map LOOPBACKS
> network 130.10.40.0 0.0.0.255 area 4
> network 130.10.134.0 0.0.0.255 area 0
> !
> ip classless
> ip http server
> !
> access-list 10 permit 130.10.41.0 0.0.0.3
> access-list 10 permit 130.10.41.4 0.0.0.3
> route-map LOOPBACKS permit 10
> match ip address 10
> !
> !
> !
>
>
>
>
>
>
>
>
> ----- Original Message -----
> From: "Kenneth Wygand" <KWygand@customonline.com>
> To: "Sergio Jimenez Arguedas" <sejimenez@its.co.cr>;
> <ccielab@groupstudy.com>
> Sent: Monday, March 15, 2004 4:32 PM
> Subject: RE: REDISTRIBUTE IN OSPF
>
>
> > Sergio,
> >
> > Seems as if you have a problem with your route-map / access list
> configuration. Can you post your configurations for at least these
sections
> (entire configs would be even better!)
> >
> > Thanks!
> > Ken
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com on behalf of Sergio Jimenez Arguedas
> > Sent: Mon 3/15/2004 3:32 PM
> > To: ccielab@groupstudy.com
> > Cc:
> > Subject: REDISTRIBUTE IN OSPF
> >
> >
> >
> > Hi Group,
> >
> >
> > I have a big problem with the following scenario:
> >
> > E0/0: Net in OSPF AREA 4
> > |
> > |
> > R4--s1/0--------------------FR_SW---------------s0/0--R1
> > FR_SW
> > R3--s1/0--------------------FR_SW
> > |
> > |
> > E0/0: Net in OSPF AREA 3
> >
> >
> > * AREA 0: OSPF Netw: point-to-multipoint //// Subnet: 130.10.134.0/24
> > R1, S0/0
> > R4, S1/0
> > R3, S1/0
> >
> >
> > *Loopbacks in R4:
> >
> > Lo0: 130.10.41.1/30
> > Lo1: 130.10.41.5/30
> >
> > *Loopbacks in R3
> >
> > Lo0: 130.10.31.1/27
> > Lo1: 130.10.31.33/27
> > Lo33: 33.33.33.3/27
> >
> >
> > ****Problem: In both R3/R4 I redistribute connected (Only int
loopbacks,
> I
> > used a route-map to avoid E0/0 to be redistribute), but R1 only received
> > Type-5: 33.33.33.0/27.
> >
> > R1 didn4t receive R3`s/R4`s Lo0, Lo1. However R1 receives Subnets of the
> Area
> > 3 and Area 4.(130.10.40.0/24&130.10.30.0/24)
> >
> >
> > Could somebody help me?
> >
> >
> > Note: I changed the ospf network type by non-broadcast but the problem
> > continue!!!
> >
> >
> >
> > Thanks,
> >
> >
> >
> > Sergio Jiminez A.
> >
> > _______________________________________________________________________
> > Please help support GroupStudy by purchasing your study materials from:
> > http://shop.groupstudy.com
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Apr 01 2004 - 08:15:30 GMT-3