From: Larry Letterman (lletterm@cisco.com)
Date: Tue Dec 02 2003 - 14:22:48 GMT-3
A 2900xl can only have one interface vlan with an ip
Address assined at active at one time..its for the
Management of the switch only....the default is int vlan 1..
Larry Letterman
Cisco Systems
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
R&S Groupstudy
Sent: Tuesday, December 02, 2003 8:52 AM
To: Church, Chuck; Weidong Xiao; rnasr; EbonyGuru@aol.com;
ccielab@groupstudy.com
Subject: RE: CAT 2900 Issue
without a doubt.
the XL switches can have multiple vlan interfaces configured with IP
addresses, but only one can be up at a time. This "up" interface is set
using the "management" command.
The 2950 switches don't use the "management" command - and you just need
to issue a no-shut on the new vlan interface for it to become active.
I have no idea why EbonyGuru@aol.com was having problems - but he said
that he needed to issue a no-shut on vlan 1 before it would work. If
this was the reason - then it would certainly make remote configuration
impossible if you were trying to change management vlans I would be
interested in knowing the exact switch model he is using...
Adam
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Church, Chuck
Sent: 02 December 2003 16:32
To: Weidong Xiao; rnasr; EbonyGuru@aol.com; ccielab@groupstudy.com
Subject: RE: CAT 2900 Issue
Maybe because it doesn't have an IP address on it? Or maybe it's some
variation in software versions?
Chuck Church
CCIE #8776, MCNE, MCSE
Wam!Net Government Services
13665 Dulles Technology Dr. Ste 250
Herndon, VA 20171
Office: 703-480-2569
Cell: 703-819-3495
cchurch@wamnetgov.com
PGP key:
http://pgp.mit.edu:11371/pks/lookup?op=index&search=cchurch%40wamnetgov.
com
> -----Original Message-----
> From: Weidong Xiao [mailto:Weidong.Xiao@vi.net]
> Sent: Tuesday, December 02, 2003 11:26 AM
> To: rnasr; Church, Chuck; EbonyGuru@aol.com; ccielab@groupstudy.com
> Subject: RE: CAT 2900 Issue
>
>
> I'm not sure about that. The following is one of our production
> switch, WS-C3548-XL, the admin vlan is vlan 999, and the vlan 1
> doesn't need to be admin shutdown.
>
>
> SW3#sh ip int b
> Any interface listed with OK? value "NO" does not have a valid
> configuration
>
> Interface IP-Address OK? Method Status
> Protocol
> VLAN1 unassigned NO unset up
> down
> VLAN999 192.168.95.203 YES NVRAM up
> up
> FastEthernet0/1 unassigned YES unset up
> up
> FastEthernet0/2 unassigned YES unset up
> up
> ....
> FastEthernet0/47 unassigned YES unset up
> up
> FastEthernet0/48 unassigned YES unset down
> down
> GigabitEthernet0/1 unassigned YES unset up
> up
> GigabitEthernet0/2 unassigned YES unset up
> up
> SW3#
>
> > -----Original Message-----
> > From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com]On Behalf Of
> > rnasr
> > Sent: 01 December 2003 15:50
> > To: 'Church, Chuck'; EbonyGuru@aol.com; ccielab@groupstudy.com
> > Subject: RE: CAT 2900 Issue
> >
> >
> > That's definetly it. You create a new int and "no shut" and the
> > other one will shut down - you can only have one vlan int active at
> > any one time on
> > these switches.
> >
> > James N.
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com]On Behalf Of
> > Church, Chuck
> > Sent: Wednesday, December 03, 2003 2:34 AM
> > To: EbonyGuru@aol.com; ccielab@groupstudy.com
> > Subject: RE: CAT 2900 Issue
> >
> >
> > Since it's a layer 2 only switch, you can only have one
> VLAN interface
> > active at a time. Is that the problem?
> >
> > Chuck Church
> > CCIE #8776, MCNE, MCSE
> > Wam!Net Government Services
> > 13665 Dulles Technology Dr. Ste 250
> > Herndon, VA 20171
> > Office: 703-480-2569
> > Cell: 703-819-3495
> > cchurch@wamnetgov.com
> > PGP key:
> > http://pgp.mit.edu:11371/pks/lookup?op=index&search=cchurch%40
> wamnetgov.com
>
> > -----Original Message-----
> > From: EbonyGuru@aol.com [mailto:EbonyGuru@aol.com]
> > Sent: Tuesday, December 02, 2003 8:30 AM
> > To: ccielab@groupstudy.com
> > Subject: CAT 2900 Issue
> >
> >
> > Dear All,
> >
> > I am currently having problems bringing a vlan interface out of
> > shutdown on the above device.
> >
> > Is there something ovbious I am missing here?
> >
> > Interface Vlan3 is shutdown and determined to remain so. Please
> > advice.
> >
> > EG.
> >
> > ______________________________________________________________
> > _________
> > Please help support GroupStudy by purchasing your study materials
> > from: http://shop.groupstudy.com
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________
> _________
> Please help support GroupStudy by purchasing your study materials
> from: http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________
> _________
> Please help support GroupStudy by purchasing your study materials
> from: http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Jan 03 2004 - 08:25:34 GMT-3