From: Aldo (febro@yahoo.com)
Date: Sat Aug 23 2003 - 12:33:16 GMT-3
I've tried that too ... I grabbed 2 new Cat5 cables, and still having
problem with the same BRI port.
It looks like hardware problem, but I just wonder whether it's due to
emutel/cisco config problem?
At 07:07 AM 8/23/2003 -0400, Jonathan V Hays wrote:
>Swap the cables where they go into the simulator and see if the problem
>stays on the same BRI port.
>
>Jonathan
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Aldo
>Sent: Saturday, August 23, 2003 3:33 AM
>To: ccielab@groupstudy.com
>Subject: Emutel Lite, Help
>
>
>Hi all,
>
>I'm having problem with my Emutel Lite ISDN Simulator as the "P" led on
>BRI-2 port does not lit up.
>
>When I power cycle the box, all leds lit up for about 1 sec, the power
>led
>stays on, and "OP" led is blinking red continuously (the manual says if
>OP
>led is blinking it means the unit is functioning correctly).
>
>I hooked up two 2503s, R1 to BRI-1, and R2 to BRI-2.
>I just configured the bare minimum on both routers with "isdn
>switch-type
>basic-dms100" command.
>I see P led lit up on BRI-1, but not on BRI-2.
>
>When I do a quick "show isdn status" command,
>R1 says "Layer 1 Status: ACTIVE", R2 says "Layer 1 Status: DEACTIVATED".
>When I swap ports (R1 to BRI-2, R2 to BRI-1),
>R1 says "Layer 1 Status: DEACTIVATED", R2 says "Layer 1 Status: ACTIVE"
>
>Am I missing something here on Emutel Lite or 2503 config?
>or do I have faulty hardware on BRI-2 port?
>Any input is appreciated. Thanks!
>
>Aldo
>
>--------------------------------
>below is my Emutel Lite setting:
>
>:: Hardware Setup
> Coms Port Baud Rate 9600
> Coms Port Parity None
> Coms Port Stop Bits 1
> Coms Port Data Bits 8
> NT/Transparent Mode NT Mode
> BRI1 Power Off
> BRI2 Power Off
> U Power Operation Normal
> S Power Operation Normal
> S Bus Timing Fixed
> Selected Tone 1000Hz @ 0dB
> BRI1/B1 Delay 0 ms
> BRI1/B2 Delay 0 ms
>
>
>:: Software Setup
> Network Type NT DMS100
> Drop Layer 2 if No Call Active Yes
> Drop Layer 1 if Layer 2 Inactive No
> Drop TEI if Layer 1 Inactive No
> Point to multipoint configuration Enter
> Service Profile IDs (SPIDs) Mandatory
> Allow Overlap Sending/Receiving No
> Numbering System Option 2 DN/2 SPID (Fixed B)
> Called Party Number Yes
> Calling Party Number Yes
> Called Party Subaddressing No
> Calling Party Subaddressing No
> High Layer Compatibility No
> Low Layer Compatibility No
> D-Channel X25 Setup Yes
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:54:05 GMT-3