From: Larry Roberts (larryr@netbeam.net)
Date: Sat Aug 23 2003 - 14:01:56 GMT-3
Aldo,
I had a similar problem with the Emutel Pro. I had to send it back to them
for repair. Contact darren@arca-technologies.com. He can troubleshoot it
over the phone and tell you if you need to send it back. They replaced mine
free of charge (except shipping I think) without any hassle. Give it a try.
Good luck,
Larry Roberts
CCIE #7886 (R&S / Security)
----- Original Message -----
From: "Aldo" <febro@yahoo.com>
To: "Jonathan V Hays" <jhays@jtan.com>; <ccielab@groupstudy.com>
Sent: Saturday, August 23, 2003 8:33 AM
Subject: RE: Emutel Lite, Help
> I've tried that too ... I grabbed 2 new Cat5 cables, and still having
> problem with the same BRI port.
> It looks like hardware problem, but I just wonder whether it's due to
> emutel/cisco config problem?
>
>
> At 07:07 AM 8/23/2003 -0400, Jonathan V Hays wrote:
> >Swap the cables where they go into the simulator and see if the problem
> >stays on the same BRI port.
> >
> >Jonathan
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> >Aldo
> >Sent: Saturday, August 23, 2003 3:33 AM
> >To: ccielab@groupstudy.com
> >Subject: Emutel Lite, Help
> >
> >
> >Hi all,
> >
> >I'm having problem with my Emutel Lite ISDN Simulator as the "P" led on
> >BRI-2 port does not lit up.
> >
> >When I power cycle the box, all leds lit up for about 1 sec, the power
> >led
> >stays on, and "OP" led is blinking red continuously (the manual says if
> >OP
> >led is blinking it means the unit is functioning correctly).
> >
> >I hooked up two 2503s, R1 to BRI-1, and R2 to BRI-2.
> >I just configured the bare minimum on both routers with "isdn
> >switch-type
> >basic-dms100" command.
> >I see P led lit up on BRI-1, but not on BRI-2.
> >
> >When I do a quick "show isdn status" command,
> >R1 says "Layer 1 Status: ACTIVE", R2 says "Layer 1 Status: DEACTIVATED".
> >When I swap ports (R1 to BRI-2, R2 to BRI-1),
> >R1 says "Layer 1 Status: DEACTIVATED", R2 says "Layer 1 Status: ACTIVE"
> >
> >Am I missing something here on Emutel Lite or 2503 config?
> >or do I have faulty hardware on BRI-2 port?
> >Any input is appreciated. Thanks!
> >
> >Aldo
> >
> >--------------------------------
> >below is my Emutel Lite setting:
> >
> >:: Hardware Setup
> > Coms Port Baud Rate 9600
> > Coms Port Parity None
> > Coms Port Stop Bits 1
> > Coms Port Data Bits 8
> > NT/Transparent Mode NT Mode
> > BRI1 Power Off
> > BRI2 Power Off
> > U Power Operation Normal
> > S Power Operation Normal
> > S Bus Timing Fixed
> > Selected Tone 1000Hz @ 0dB
> > BRI1/B1 Delay 0 ms
> > BRI1/B2 Delay 0 ms
> >
> >
> >:: Software Setup
> > Network Type NT DMS100
> > Drop Layer 2 if No Call Active Yes
> > Drop Layer 1 if Layer 2 Inactive No
> > Drop TEI if Layer 1 Inactive No
> > Point to multipoint configuration Enter
> > Service Profile IDs (SPIDs) Mandatory
> > Allow Overlap Sending/Receiving No
> > Numbering System Option 2 DN/2 SPID (Fixed B)
> > Called Party Number Yes
> > Calling Party Number Yes
> > Called Party Subaddressing No
> > Calling Party Subaddressing No
> > High Layer Compatibility No
> > Low Layer Compatibility No
> > D-Channel X25 Setup Yes
> >
> >
> >_______________________________________________________________________
> >You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >_______________________________________________________________________
> >You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:54:05 GMT-3