From: a9605355 (a9605355@graduate.hku.hk)
Date: Tue Jul 22 2003 - 22:39:38 GMT-3
have you tried :
show ip rip database to verify ?
>===== Original Message From "Mustafa Bayramov (ICT/IT)"
<mustafa@azercell.com> =====
>Also check your IOS versions I remember IOS 12.1.X had bug related to
>tagging RIPv2.
>
>
>Regards
>
>
>Mustafa M Bayramov
>
>CISSP
>CCNP,CCDP,Cisco Security Specialist
>Network engineer and security analyst
>
>"I know nothing except the fact of my ignorance." Socrates
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Jonathan V Hays
>Sent: Tuesday, July 22, 2003 4:49 PM
>To: 'Banlan Chen'; ccielab@groupstudy.com
>Subject: RE: redistribution between ospf and rip2
>
>Try assigning default metrics.
>
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Banlan Chen
>Sent: Tuesday, July 22, 2003 4:08 PM
>To: ccielab@groupstudy.com
>Subject: redistribution between ospf and rip2
>
>
>Hi All,
>
>I am tring to mutual redistribute ospf and rip2 with tag, but it doesn't
>work. from RIP side I can see the ospf routes, but at ospf side I can't
>see any routes from RIP. Could someone figure out what's problem in my
>configuration. Thanks a lot.
>
>interface Loopback0
>ip address 150.50.6.6 255.255.255.255
>!
>interface Ethernet0
>ip address 150.50.100.6 255.255.255.0
>!
>interface Serial0
>ip address 150.50.10.6 255.255.255.0
>encapsulation frame-relay
>ip ospf network point-to-point
>frame-relay map ip 150.50.10.2 421 broadcast
>frame-relay map ip 150.50.10.6 421
>frame-relay lmi-type ansi
>!
>router ospf 1
>log-adjacency-changes
>redistribute rip subnets route-map rip-os
>network 150.50.6.6 0.0.0.0 area 0
>network 150.50.10.0 0.0.0.255 area 0
>!
>router rip
>version 2
>redistribute ospf 1 metric 1 route-map os-rip
>passive-interface default
>no passive-interface Ethernet0
>network 150.50.0.0
>!
>route-map os-rip deny 10
>match tag 120
>!
>route-map os-rip permit 20
>set tag 110
>!
>route-map rip-os deny 10
>match tag 110
>!
>route-map rip-os permit 20
>set tag 120
>--
>
>--------- Original Message ---------
>
>DATE: Fri, 18 Jul 2003 19:19:11
>From: "Banlan Chen" <banlan.chen@lycos.com>
>To: ccielab@groupstudy.com
>Cc:
>
>>Hi Group,
>>
>>When I configure RIP over two FR main interfaces, I should enable
>split-horizon on each interface or just enable it at one of these
>interfaces.
>>Under ATM interface, Do I need configure ip split-horizon for RIP and
>EIGRP?
>>Thanks in advance.
>>
>>Banlan
>>
>>
>>____________________________________________________________
>>Get advanced SPAM filtering on Webmail or POP Mail ... Get Lycos Mail!
>>http://login.mail.lycos.com/r/referral?aid=27005
>>
>>
>>_______________________________________________________________________
>>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>>
>>Subscription information may be found at:
>>http://www.groupstudy.com/list/CCIELab.html
>>
>
>
>
>____________________________________________________________
>Get advanced SPAM filtering on Webmail or POP Mail ... Get Lycos Mail!
>http://login.mail.lycos.com/r/referral?aid=27005
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Aug 06 2003 - 06:52:49 GMT-3