From: cchorao@xtra.co.nz
Date: Tue Apr 29 2003 - 17:59:54 GMT-3
Jonathan I think Tom is referring to the main int , not sub int.
Carlos
>
> From: "Jonathan V Hays" <jhays@jtan.com>
> Date: 2003/04/30 Wed AM 05:07:24 GMT+12:00
> To: "'Tom Young'" <gitsyoung@yahoo.co.jp>, "'Carlos'"
> <cchorao@xtra.co.nz>
> CC: <ccielab@groupstudy.com>
> Subject: RE: the multipoint main interface
>
> Tom,
>
> There isn't any default - you must specify which one you want:
>
> Router(config-if)#encapsulation frame-relay
> Router(config-if)#exit
> Router(config)#in s0.1
> % Incomplete command.
> Router(config)#in s0.1 ?
> multipoint Treat as a multipoint link
> point-to-point Treat as a point-to-point link
>
> Hope that helps.
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > Behalf Of Tom Young
> > Sent: Tuesday, April 29, 2003 8:00 AM
> > To: Carlos
> > Cc: ccielab@groupstudy.com
> > Subject: Re: the multipoint main interface
> >
> >
> > Thanks for your reply, you means if I use the f/r , the
> > default type for serial port is multipoint ? But could I
> > set the for point-to-point ?
> >
> >
> > THanks again
> >
> >
> > --- Carlos <cchorao@xtra.co.nz> $B$+$i$N%a%C%;!<%8!'(B
> > > Tom ,
> > >
> > > I assume you are referring to frame-relay for
> > > encapsulation ?
> > > Config in the main interface operates as mulitpoint
> > > by default.
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > Carlos Chorao (CCIE 11351 R&S)
> > >
> > > Senior Technical Consultant
> > > Telecom New Zealand
> > > Advanced Solutions Group -Network Design and
> > > Security
> > >
> > > Network Security and Design
> > > ----- Original Message -----
> > > From: "Tom Young" <gitsyoung@yahoo.co.jp>
> > > To: <ccielab@groupstudy.com>
> > > Sent: Tuesday, April 29, 2003 8:57 PM
> > > Subject: the multipoint main interface
> > >
> > >
> > > > Hi, group
> > > >
> > > > If I use the subinterface of serial port to
> > > connecting
> > > > several remote office, I could set the multipoint
> > > for it,
> > > > but if I use the main interface, not the
> > > subinterface ,
> > > > Can I still set it for multipoint? I couldn't
> > > found the
> > > > command.
> > > >
> > > > Thanks alot
> > > >
> > > > __________________________________________________
> > > > Do You Yahoo!?
> > > > Yahoo! BB is Broadband by Yahoo!
> > > http://bb.yahoo.co.jp/
> > > >
> > >
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Yahoo! BB is Broadband by Yahoo! http://bb.yahoo.co.jp/
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:36:09 GMT-3