From: Wayne Hines (wayneh@DataNetDev.com.au)
Date: Wed Apr 23 2003 - 08:37:54 GMT-3
Hello All,
Has anyone identified a solution to tftp/ftp boot commands not completing.
If have attempted a number of variations on
boot system tftp c1700-bk9no3r2sy7-mz.122-11.T.bin 172.16.30.93
boot system ftp c1700-bk9no3r2sy7-mz.122-11.T.bin 172.16.30.93 (with
anonymous login and user based login)
with config-register 0x2102 or
config-register 0x10F
and yes the archives have been checked as well as various cisco sources
including http://www.cisco.com/warp/public/63/install_tftp.html
Note different tftp/ftp servers (cisco's and the more stable 3com's) have
been tested, both with directed connections and switch based connections.
The transfer starts then hangs after ~11-12K (both tftp/ftp). ( I have
done this successfully with many other routers) but not this 1720. It is
not an issue with the image as other image loads also fail.
Varying error messages result, with the most consistent being
%SYS-6-READ_BOOTFILE_FAIL: tftp://172.16.30.93/c1700-k9o3sy7-mz.122-11.T.bin
Fil
e read failed -- Unknown error 0.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
boot of "tftp:c1700-k9o3sy7-mz.122-11.T.bin 172.16.30.93" using boot helper
"fla
sh:c1700-k9o3sy7-mz.122-11.T.bin" failed
error returned: File read failed -- Unknown error 0
loadprog: error - on file open
boot: cannot load "tftp:c1700-k9o3sy7-mz.122-11.T.bin 172.16.30.93"
R1#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-K9O3SY7-M), Version 12.2(11)T, RELEASE
SOFTWARE
(fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 31-Jul-02 10:15 by ccai
Image text-base: 0x80008124, data-base: 0x80D4FF48
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
R1 uptime is 38 minutes
System returned to ROM by power-on
System image file is "flash:c1700-k9o3sy7-mz.122-11.T.bin"
cisco 1720 (MPC860T) processor (revision 0x601) with 27853K/4915K bytes of
memor
y.
Processor board ID JAD05190LXN (1513744447), with hardware revision 0000
MPC860T processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Mystified!!!!!! Are MTU setting required? Flow control perhaps?? ???
Wayne Hines
B.Sc., M.Sc., CMACS Proj. Man., CSS1, CCDP+Net. Man.+Voice+ATM, CCNP, CNE,
MCNE, MCSE
Database & Network Developers - your Cisco Premier Partner / Novell Business
Partner
Mailing: P.O. Box 14283 Melbourne 8001
Email: wayneh@DataNetDev.com.au
Web: http://www.DataNetDev.com.au/
Tel: +61 (0)3 9329 6444
Mobile: +61 (0)41 152 4486
This archive was generated by hypermail 2.1.4 : Thu May 01 2003 - 13:36:02 GMT-3