From: Evgeny Tantsura (ivgen@castel.nl)
Date: Thu Jan 02 2003 - 14:25:06 GMT-3
The whole problem was ip ospf demand-circuit command on the calling router
and thus no ip traffic as expected.
> It seems that you configure the watch-list to track on a host route - 192.168.5.1/32 - "dialer watch-list 1 ip 192.168.5.1 255.255.255.255". Note that if there is no such route in routing table on the 1st router (has watch-list configured) come from the primary interface (being watch-group), watch-list will activate the dialing. But you may want to take "ospf demand-circuit" into the equation. If you have ospf demand-circuit configured, you should not block the ospf traffic on the dialer-list. ospf demand-circuit will take care of the hello suppression. That makes me think that the reason to dial is not by watch-list, it is rather from the 2nd router (w/o watch-list) for ospf adj. Check with "show dialer" on both routers to find out.
>
> It would be great if you can provide the complete configuration on both routers.
>
> Sam
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Evgeny Tantsura
> Sent: Thursday, January 02, 2003 10:04 AM
> To: ccielab@groupstudy.com
> Subject: ISDN Backup With Dialer Watch
>
>
> Hi,
>
> My ISDN interface with Dialer Watch on it
> is going down every idle-timeout and then dialing again.
>
> interface Dialer1
> ip address 1.1.1.2 255.255.255.0
> encapsulation ppp
> ip ospf demand-circuit
> dialer pool 1
> dialer idle-timeout 180
> dialer string 0496406937
> dialer load-threshold 127 either
> dialer watch-group 1
> dialer-group 1
> pulse-time 0
> no cdp enable
> ppp authentication chap
> ppp multilink
> end
>
> access-list 170 deny ospf any any
> access-list 170 permit ip any any
> dialer watch-list 1 ip 192.168.5.1 255.255.255.255
> dialer-list 1 protocol ip list 170
> ----------------------------------------------------
>
> interface Dialer1
> ip address 1.1.1.1 255.255.255.0
> encapsulation ppp
> dialer pool 1
> dialer idle-timeout 180
> dialer load-threshold 50 either
> dialer-group 1
> no cdp enable
> ppp authentication chap
>
> dialer-list 1 protocol ip permit
>
>
> According to CCO it should stay connected until the router gets the
> route via primery interface.
>
> Any idea's ?
>
> With kind regards/ met vriendelijke groeten,
> ------------------------------------------------
> E. Tantsura
> Network Developer
> Essent Kabelcom N.V.
> Dr.van Deenweg 84
> 8025BN Zwolle, The Netherlands
> Tel: +31-(0)38-850-7642
> Fax: +31-(0)38-850-7410
> Mob: +31-(0)6-290-80458
> ------------------------------------------------
> .
> .
With kind regards/ met vriendelijke groeten,
------------------------------------------------
E. Tantsura
Network Developer
Essent Kabelcom N.V.
Dr.van Deenweg 84
8025BN Zwolle, The Netherlands
Tel: +31-(0)38-850-7642
Fax: +31-(0)38-850-7410
Mob: +31-(0)6-290-80458
------------------------------------------------
.
This archive was generated by hypermail 2.1.4 : Sat Feb 01 2003 - 07:33:39 GMT-3