From: dotun Ayodeji (dotun2k2@xxxxxxxxxxx)
Date: Wed Jul 24 2002 - 01:44:27 GMT-3
This is not working because you need to assign a local-dlci to both sides. i
have actually done this before. So the DCE side will be frame-relay local
dlci 102 and the DCE side will be frame-relay local dlci 101
See if that helps
>From: "Dotun Oni" <dot_oni@hotmail.com>
>Reply-To: "Dotun Oni" <dot_oni@hotmail.com>
>To: Justin.Cook@computerland.co.nz, ciscoworks2001@yahoo.com,
>ccielab@groupstudy.com
>Subject: RE: Frame Relay NO Sub-interfaces
>Date: Tue, 23 Jul 2002 16:54:53 -0700
>
>Try using same dlci on both sides.
>
>D
>
>
>>From: Justin Cook <Justin.Cook@computerland.co.nz>
>>Reply-To: Justin Cook <Justin.Cook@computerland.co.nz>
>>To: Armand D <ciscoworks2001@yahoo.com>, ccielab@groupstudy.com
>>Subject: RE: Frame Relay NO Sub-interfaces
>>Date: Wed, 24 Jul 2002 09:54:21 +1200
>>
>>You require a Frame Switch, Back to Back will not work, you require a unit
>>to forward the DLCIs (Layer2) between your routers so in essence the Frame
>>Relay Switch maps you dlcis between the router/s
>>
>>Check ou this link, it shows you how to configure a Frame Relay Switch
>>
>>http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_
>>c/wcdfrely.htm
>>
>>--
>>Justin Cook
>>
>>
>>-----Original Message-----
>>From: Logan, Harold [mailto:loganh@mccfl.edu]
>>Sent: Wednesday, 24 July 2002 8:46 a.m.
>>To: Armand D; ccielab@groupstudy.com
>>Subject: RE: Frame Relay NO Sub-interfaces
>>
>>I've never done back-to-back FR with frame map statements, try using frame
>>interface-dlci instead, and use the same dlci on both routers. Also, you
>>need to put 'no keepalive' on both ends.
>>
>>hth,
>>
>>Hal
>>
>> > -----Original Message-----
>> > From: Armand D [mailto:ciscoworks2001@yahoo.com]
>> > Sent: Tuesday, July 23, 2002 4:01 PM
>> > To: ccielab@groupstudy.com
>> > Subject: Frame Relay NO Sub-interfaces
>> >
>> >
>> > Hello,
>> >
>> > I'm wondering if anyone has a sample config for a
>> > Frame Relay back to back using no subinterfaces. I
>> > have the following configurations on my routers. Both
>> > routers show interface status UP DOWN and PVC status
>> > inactive.
>> >
>> >
>> > DTE Side:
>> >
>> > Interface s0
>> > encap frame-relay
>> > ip add 10.0.0.1 255.255.255.0
>> > frame-Relay map ip 10.0.0.2 101 broadcast
>> > frame-relay lmi-type cisco
>> >
>> > DCE Side:
>> > Ineterface s0
>> > encap frame-relay
>> > ip add 10.0.0.2 255.255.255.0
>> > Frame-Relay map ip 10.0.0.1 102 broadcast
>> > clock rate 128000
>> > frame-relay lmi-type cisco
>> >
>> >
>> > Any tips would be great.
>> >
>> > Thanks,
>> >
>> > Armand
>> >
>> >
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:36:41 GMT-3