From: dunne.brian@xxxxxxxxxxxx
Date: Tue Apr 30 2002 - 14:47:59 GMT-3
----- Forwarded by Brian Dunne/ADLittle on 05/01/2002 01:46 AM -----
Brian Dunne
To: Eric <namaste@pacbell.net>
05/01/2002 cc:
01:44 AM bcc:
Subject: Re: 7000 boot(Document li
nk: Brian Dunne)
Eric,
I've tried all possible commands for boot system--the unit still cycles.
Also, I can't even get to enable mode w/out it recycling after a break.
Let me know what you think... notice below error in rxboot---trying rom...
Regards,
Brian
>boot system flash
boot: bootload_rp1(system flash, C0000000, 2, D72)
boot: type indirect, booting [system flash] via [rom] rxboot
boot: recursing bootload_rp1(rom, 0, 0, 0)
boot: type direct, method rom
boot: booting ROM image
boot: unpacking rom - 3924851
F3: 8668+3916151+165008 at 0x1000
boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xD72, 0x1000)
Self decompressing the image :
#################################################
###############################################################################
#
#################################### [OK]
Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
(PC)
Error in rxboot, trying ROM
boot: changing BOOTLDR from [] to default
System Bootstrap, Version 11.1(5), SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
RP1 processor with 16384 Kbytes of main memory
boot: FASTBOOT disabled
boot: bootload_rp1(cisco2-rp1, 40000000, 2, F50)
boot: type indirect, booting [cisco2-rp1] via [rom] rxboot
boot: recursing bootload_rp1(rom, 0, 0, 0)
boot: type direct, method rom
boot: booting ROM image
boot: unpacking rom - 3924851
F3: 8668+3916151+165008 at 0x1000
boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xF50, 0x1000)
Self decompressing the image :
#################################################
###############################################################################
#
#################################### [OK]
Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
(PC)
Error in rxboot, trying ROM
boot: changing BOOTLDR from [] to default
System Bootstrap, Version 11.1(5), SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
RP1 processor with 16384 Kbytes of main memory
boot: bootload_rp1(, 40000000, 2, 0)
boot: type direct, method rom
boot: booting ROM image
<<<repeat>>>
>boot system flash:
boot: bootload_rp1(system flash:, C0000000, 2, DCE)
boot: type indirect, booting [system flash:] via [rom] rxboot
boot: recursing bootload_rp1(rom, 0, 0, 0)
boot: type direct, method rom
boot: booting ROM image
boot: unpacking rom - 3924851
F3: 8668+3916151+165008 at 0x1000
boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xDCE, 0x1000)
Self decompressing the image :
#################################################
###############################################################################
#
#################################### [OK]
Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
(PC)
Error in rxboot, trying ROM
boot: changing BOOTLDR from [] to default
System Bootstrap, Version 11.1(5), SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
RP1 processor with 16384 Kbytes of main memory
<<repeat>>
Eric
<namaste@pacb To: dunne.brian@adlittle.com
ell.net> cc:
bcc:
05/01/2002 Subject: Re: 7000 boot
01:07 AM
http://www.cisco.com/univercd/cc/td/doc/product/core/cis7505/frus/2083flmc.htm#
36526
To enable booting from Flash memory, set configuration register bits 3, 2,
1, and 0
to a value between 2 and 15 in conjunction with the boot system flash
[filename]
configuration
command.
Following are definitions of the various Flash memory-related boot
commands:
boot system flash?Boots the first file in onboard Flash memory
boot system flash:?Boots the first file in onboard Flash memory
boot system flash herfile?Boots the file named "herfile" on onboard Flash
memory
boot system flash slot0:?Boots the first file on Flash memory card in slot
0
boot system flash flash:hisfile ?Boots the first file named "hisfile" on
onboard
Flash memory
boot system flash slot0:myfile ?Boots the file named "myfile" on the Flash
memory
card in slot 0
Enter configuration mode and specify a Flash memory filename in the PC Card
slot
from which to boot by using the configure terminal command, as follows:
Router# configure terminal
Enter configuration commands, one per line. End with CTRL-Z.
Router(config)# boot system flash slot0:myfile
Disable Break and enable the boot system flash slot0: command using the
config-register command. Use the value shown in the following example:
Router(config)# config-reg 0x2102
dunne.brian@adlittle.com wrote:
> Hi--
>
> I'm wondering if anyone knows of the below problem.
>
> This is on a 7000 router, and I've tried several valid combinations of
> config-register to avoid this process----after breaking from the boot
> sequence. The "boot error" light on the RP goes on after each sequence.
> I'll try any solutions suggested, just don't tell me this is hardware
> related ; ) .....(e-bay )
>
> Is there a config-register value I'm missing? Flash card is in the unit,
> but I can not access it after break w/out the unit re-cycling.
>
> Regards---
>
> Use, duplication, or disclosure by the Government is
> subject to restrictions as set forth in subparagraph
> (c) of the Commercial Computer Software - Restricted
> Rights clause at FAR sec. 52.227-19 and subparagraph
> (c) (1) (ii) of the Rights in Technical Data and Computer
> Software clause at DFARS sec. 252.227-7013.
>
> cisco Systems, Inc.
> 170 West Tasman Drive
> San Jose, California 95134-1706
>
> Cisco Internetwork Operating System Software
> IOS (tm) GS Software (GS7-J-M), Version 11.1(5), RELEASE SOFTWARE (fc1)
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Mon 05-Aug-96 17:00 by mkamson
> Image text-base: 0x00001000, data-base: 0x00788EDC
>
> Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
> (PC)
> boot: reset autoboot
>
> System Bootstrap, Version 11.1(5), SOFTWARE
> Copyright (c) 1986-1994 by cisco Systems
> RP1 processor with 16384 Kbytes of main memory
> boot: FASTBOOT disabled
> boot: bootload_rp1(cisco2-rp1, 40000000, 2, F50)
> boot: type indirect, booting [cisco2-rp1] via [rom] rxboot
> boot: recursing bootload_rp1(rom, 0, 0, 0)
> boot: type direct, method rom
> boot: booting ROM image
> boot: unpacking rom - 3924851
> F3: 8668+3916151+165008 at 0x1000
> boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xF50, 0x1000)
> Self decompressing the image :
> #################################################
>
###############################################################################
#
> #################################### [OK]
> Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
> (PC)
> Error in rxboot, trying ROM
> boot: changing BOOTLDR from [] to default
>
> System Bootstrap, Version 11.1(5), SOFTWARE
> Copyright (c) 1986-1994 by cisco Systems
> RP1 processor with 16384 Kbytes of main memory
> boot: FASTBOOT disabled
> boot: bootload_rp1(cisco2-rp1, 40000000, 2, F50)
> boot: type indirect, booting [cisco2-rp1] via [rom] rxboot
> boot: recursing bootload_rp1(rom, 0, 0, 0)
> boot: type direct, method rom
> boot: booting ROM image
> boot: unpacking rom - 3924851
> F3: 8668+3916151+165008 at 0x1000
> boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xF50, 0x1000)
> Self decompressing the image :
> #################################################
>
###############################################################################
#
> #################################### [OK]
> Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
> (PC)
> Error in rxboot, trying ROM
> boot: changing BOOTLDR from [] to default
>
> System Bootstrap, Version 11.1(5), SOFTWARE
> Copyright (c) 1986-1994 by cisco Systems
> RP1 processor with 16384 Kbytes of main memory
> boot: FASTBOOT disabled
> boot: bootload_rp1(cisco2-rp1, 40000000, 2, F50)
> boot: type indirect, booting [cisco2-rp1] via [rom] rxboot
> boot: recursing bootload_rp1(rom, 0, 0, 0)
> boot: type direct, method rom
> boot: booting ROM image
> boot: unpacking rom - 3924851
> F3: 8668+3916151+165008 at 0x1000
> boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xF50, 0x1000)
> Self decompressing the image :
> #################################################
>
###############################################################################
#
> #################################### [OK]
> Local Timeout (control reg=0xF910) Error, address: 0x4AFC4AFE at 0x1C811E
> (PC)
> Error in rxboot, trying ROM
> boot: changing BOOTLDR from [] to default
>
> System Bootstrap, Version 11.1(5), SOFTWARE
> Copyright (c) 1986-1994 by cisco Systems
> RP1 processor with 16384 Kbytes of main memory
> boot: FASTBOOT disabled
> boot: bootload_rp1(cisco2-rp1, 40000000, 2, F50)
> boot: type indirect, booting [cisco2-rp1] via [rom] rxboot
> boot: recursing bootload_rp1(rom, 0, 0, 0)
> boot: type direct, method rom
> boot: booting ROM image
> boot: unpacking rom - 3924851
> F3: 8668+3916151+165008 at 0x1000
> boot: system_state [SYSTATE_BOOTING], ram_dispatch(2, 0xF50, 0x1000)
> Self decompressing the image : ##################################
> Abort at 0x1DBC (PC)
> >^@^@^@^@^@
> >
> >
>
> **** This is intended for the addressee only and may contain
> confidential business information. It may not be copied
> without our permission. If you are not the intended recipient,
> please contact the sender as soon as possible and
> delete the material from any computer.****
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:58:24 GMT-3