From: John Neiberger (neiby@xxxxxxxxxx)
Date: Sat Mar 23 2002 - 13:16:07 GMT-3
I'm going to make a guess here. For SRB to work, the end
devices must be aware that they are using SRB. This is
obviously not the case with TB.
In your lab, when you had your router configured for SRB, did
you have your workstations also configured for SRB? If not,
that might explain why your SRB setup didn't work but your TB
setup did.
I just woke up so don't blame me if I completely wrong. :-)
John
---- On Sat, 23 Mar 2002, Lupi, Guy (Guy.Lupi@eurekaggn.com)
wrote:
> Ok, here it is next weekend, and I have set up this scenario
again.
> Here is
> the output and config of r3 when it is NOT working:
>
> r3#sh conf
> Using 960 out of 32762 bytes
> !
> version 12.1
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r3
> !
> no logging console
> !
> !
> !
> !
> !
> ip subnet-zero
> no ip domain-lookup
> !
> !
> !
> !
> !
> source-bridge ring-group 12
> dlsw local-peer peer-id 3.3.3.3 group 83 cost 1 lf 1500
> dlsw remote-peer 0 tcp 8.8.8.8 lf 1500
> !
> interface Loopback0
> ip address 3.3.3.3 255.255.255.255
> !
> interface Serial0
> ip address 3.8.3.3 255.255.255.0
> no fair-queue
> !
> interface Serial1
> no ip address
> shutdown
> !
> interface TokenRing0
> ip address 33.33.33.33 255.255.255.0
> ring-speed 16
> source-bridge 1 1 12
> source-bridge spanning
> !
> interface BRI0
> no ip address
> shutdown
> isdn x25 static-tei 0
> !
> router ospf 100
> log-adjacency-changes
> passive-interface TokenRing0
> network 3.3.3.3 0.0.0.0 area 0
> network 3.8.3.0 0.0.0.255 area 0
> network 198.207.193.0 0.0.0.0 area 0
> !
> ip classless
> ip http server
> !
> !
> bridge 1 protocol ieee
> !
> line con 0
> line aux 0
> line vty 0 4
> !
> end
>
> r3#sh dlsw reach
> DLSw Local MAC address reachability cache list
> Mac Addr status Loc. port rif
> 0000.306c.cf50 FOUND LOCAL TokenRing0
0690.0011.00C0
>
> DLSw Remote MAC address reachability cache list
> Mac Addr status Loc. peer
>
> DLSw Local NetBIOS Name reachability cache list
> NetBIOS Name status Loc. port rif
>
> DLSw Remote NetBIOS Name reachability cache list
> NetBIOS Name status Loc. peer
>
> r3#sh dlsw peer
> Peers: state pkts_rx pkts_tx type
drops ckts TCP
> uptime
> TCP 8.8.8.8 CONNECT 38 59 conf
0 0 0
> 00:11:19
> Total number of connected peers: 1
> Total number of connections: 1
>
> r3#
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:57:19 GMT-3