From: Brian Dennis (brian@xxxxxx)
Date: Thu Jan 10 2002 - 20:05:22 GMT-3
One more tidbit....
If you need to test connectivity in a lab environment without access to two
hosts, use the Catalyst 5000 management interface (sc0) and the Catalyst
3920's BRFs. It's easy to move the sc0 interface on the Catalyst 5000 around
to different VLANs (change the IP address and default gateway also) and put
IP addresses on the BRF's inside the 3920 for testing. We use them in class
to test things like ACL's, IPSec, etc.
Brian Dennis, CCIE #2210 (R&S)(ISP/Dial) CCSI #98640
5G Networks, Inc.
brian@5g.net
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Brian Dennis
Sent: Thursday, January 10, 2002 2:07 PM
To: ccielab@groupstudy.com
Subject: RE: at the lab exam
A couple more tidbits....
Setup HyperTerminal to the largest "backscroll buffer lines" number it will
take so you can go back and see what a routing table looked like or what a
config looked like earlier in the day if the need arises. This of course in
under the properties settings (File... Properties....Settings) in
HyperTerminal. You may also setup HyperTerminal to cature everything to a
file using the capture text option. This is under (Transfer....Capture
Text).
Your routers and switches should be able to survive a reload. I would advise
right before lunch saving all the configs. Then reload your routers and
switches and see if everything is still working when you come back from
lunch. As you know certain things can change when a reload happens. Also
somethings may even start working after the reload that didn't work before
;-)
Brian Dennis, CCIE #2210 (R&S)(ISP/Dial) CCSI #98640
5G Networks, Inc.
brian@5g.net
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
EA Louie
Sent: Thursday, January 10, 2002 1:33 PM
To: ccielab@groupstudy.com
Subject: Re: at the lab exam
great tool - thanks for sharing it - I'll use it on Tuesday
-e-
----- Original Message -----
From: "Brian Dennis" <brian@5g.net>
To: <ccielab@groupstudy.com>
Sent: Thursday, January 10, 2002 1:14 PM
Subject: RE: at the lab exam
> You also could make a sort of table to use while reading over the lab.
Mark
> down which devices need to be configured for each section. Then as you do
> the sections mark off (i.e. circle) what devices have been done. See
below:
>
> Device R1 R2 R3 R4 R5 Cat5
> Section
> 1.1 x x
> 1.2 x x x x
> 1.3 x x
> 2.1 x x
>
>
> A student of mine came up with this idea and I thought it was pretty cool.
>
> Brian Dennis, CCIE #2210 (R&S)(ISP/Dial) CCSI #98640
> 5G Networks, Inc.
> brian@5g.net
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Mas Kato
> Sent: Thursday, January 10, 2002 12:44 PM
> To: yusman@mastersystem.co.id
> Cc: ccielab@groupstudy.com
> Subject: RE: at the lab exam
>
>
> [demime could not interpret encoding binary - treating as plain text]
> I would suggest reading through the whole assignment not just once, but
> twice before charging in. On the first pass, look for issues and order
> dependencies. On the second pass look for absolutes--absolute values to be
> used, ranges to be covered, etc.--note these and then go for it!
>
> Best of luck,
>
> Mas Kato
> https://ecardfile.com/id/mkato
>
> > Yusman@mastersystem.co.id at the lab exam ccielab@groupstudy.comDate:
Thu,
> 10 Jan 2002 18:31:05 +0700
> >Reply-To: Yusman@mastersystem.co.id
> >
> >For the first attempt lab exam, what is the best, read the whole lab
> >instruction then do the lab or read per section task then do the test,
> >without wasting the time
> >
> >Thanks for the opinion
> ------------------------------------------------------------
> Speed Racer's Official Virtual Pit Stop.
> http://www.speedracerdsl.com/speedracer/
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:56:23 GMT-3