From: Michael Popovich (m.popovich@xxxxxxxx)
Date: Sun Dec 16 2001 - 13:52:31 GMT-3
I have had good luck buying new from www.crucial.com They also have free
2-day FedEx shipping. Might check it out.
MP
----- Original Message -----
From: "Annu" <annu_roopa@yahoo.com>
To: "kym blair" <kymblair@hotmail.com>
Cc: <ccielab@groupstudy.com>
Sent: Sunday, December 16, 2001 8:39 AM
Subject: RE: Cisco 2514 Upgrade Problem
> Kym,
>
> Thanks for u reply,not a problem.In fact I suspect bad
> flash bcoz of parity error (may be wrong).Anyway any
> idea where we can get reasonable and problem-free
> Flash and Memory for routers 2500-2600 !
>
> Thanks for ur time and answers
> Annu.
>
>
>
> --- kym blair <kymblair@hotmail.com> wrote:
> > Annu,
> >
> > You haven't got an IOS loaded on your flash (maybe
> > that is what you said in
> > earlier emails). Anyway, set your config-reg to
> > 0x41 and reload ("4" says
> > to ignore startup-config, and "1" says to boot from
> > image in bootrom rather
> > than image in flash). Config your ethernet 0 port
> > with an IP on your LAN,
> > and of course do "no shutdown" on E0. Ping your
> > tftpserver (either a
> > workstation or another 2500 router with the IOS you
> > want to copy); if the
> > tftpserver is on a different network, you'll have to
> > set the default gateway
> > on your 2514 (probably not necessary if you're
> > working at home). Run "copy
> > tftp flash". Once the IOS is copied into your new
> > 2514, set the config-reg
> > back to 0x2102 and reload again. Once it comes up,
> > "copy running start" so
> > your startup-config is based on the current IOS.
> >
> > Kym
> >
> >
> >
> > >From: Annu <annu_roopa@yahoo.com>
> > >Reply-To: Annu <annu_roopa@yahoo.com>
> > >To: Young Brown <lybrown@cisco.com>,
> >
> > >CC: elouie@yahoo.com
> > >Subject: RE: Cisco 2514 Upgrade Problem
> > >Date: Sat, 15 Dec 2001 17:17:54 -0800 (PST)
> > >
> > >Young/EA/Group,
> > >
> > >Young: Well i went thru the URL/Doc for Error
> > Decoding
> > >which u sent and it looks from that there are
> > commands
> > >not supported in current version of code.
> > >
> > >EA:I have sufficient memory and Flash.Here is an
> > >output of the commands.
> > >-------------------------
> > >r12(boot)#sho ver
> > >Cisco Internetwork Operating System Software
> > >IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R),
> > Version
> > >11.0(10c), RELEASE SOFTWARE (fc1)
> > >Copyright (c) 1986-1996 by cisco Systems, Inc.
> > >Compiled Fri 27-Dec-96 17:33 by loreilly
> > >Image text-base: 0x01010000, data-base: 0x00001000
> > >
> > >ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
> > >
> > >r12 uptime is 6 minutes
> > >System restarted by power-on
> > >Running default software
> > >
> > >cisco 2500 (68030) processor (revision L) with
> > >14336K/2048K bytes of memory.
> > >Processor board ID 07094835, with hardware revision
> > >00000000
> > >X.25 software, Version 2.0, NET2, BFE and GOSIP
> > >compliant.
> > >2 Ethernet/IEEE 802.3 interfaces.
> > >2 Serial network interfaces.
> > >32K bytes of non-volatile configuration memory.
> > >16384K bytes of processor board System flash
> > >(Read/Write)
> > >
> > >Configuration register is 0x2102
> > >
> > >--------
> > >r12(boot)#show flash detailed
> > >System flash directory:
> > >No files in System flash
> > >[0 bytes used, 16777216 available, 16777216 total]
> > >16384K bytes of processor board System flash
> > >(Read/Write)
> > >
> > >---------
> > >r12(boot)#show flash err
> > >
> > >System flash directory:
> > >No files in System flash
> > >[0 bytes used, 16777216 available, 16777216 total]
> > >16384K bytes of processor board System flash
> > >(Read/Write)
> > >
> > > Chip Bank Code Size Name
> > > erase write
> > > 1 1 01AD 2048KB AMD
> > 29F016
> > > 0 0
> > > 2 1 01AD 2048KB AMD
> > 29F016
> > > 0 0
> > > 3 1 01AD 2048KB AMD
> > 29F016
> > > 0 0
> > > 4 1 01AD 2048KB AMD
> > 29F016
> > > 0 0
> > > 1 2 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 2 2 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 3 2 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 4 2 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 1 3 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 2 3 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 3 3 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > > 4 3 89A2 1024KB INTEL
> > 28F008SA
> > > 0 0
> > >
> > >Please let me know. What exactly is the problem.
> > >thanks for ur time and replies.
> > >
> > >Annu
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:43 GMT-3