From: Charles Huang (CharlesNY2000@xxxxxxxxx)
Date: Wed Nov 28 2001 - 19:46:58 GMT-3
there is NO local-peer option in source route bridging. ( only in DLSW )
Guy is right, you need 2 remote peer statement, one is local ip and the other i
s the remote ip.
Charles
----- Original Message -----
From: "Lupi, Guy" <Guy.Lupi@eurekaggn.com>
To: "'Brion Washington '" <CCIE6200@home.com>; <ccielab@groupstudy.com>
Sent: Wednesday, November 28, 2001 4:26 PM
Subject: RE: Source Route Bridging
> I don't have a local peer option, the only peer option is the remote peer,
> according to cco one of the remote peer statements should be an ip of the
> local router, and one should be the ip of the actual remote peer. When I do
> a source-bridge ? I get the following:
>
> R4(config)#source-bridge ?
> connection-timeout Connection timeout
> cos-enable Prioritize traffic by Class of Service
> enable-80d5 Convert TR LLC2 frames to Ethernet type 80d5
> frames
> explorer-dup-ARE-filter Enable filtering of duplicate all-routes
> explorers
> explorer-fastswitch Enable local explorer fastswitching
> explorer-maxrate Maximum SRB local explorer data rate in bytes/sec
> explorerQ-depth Maximum SRB explorer queue depth per interface
> fst-peername Fast Sequence Transport local interface address
> keepalive Enable RSRB remote peer keepalive
> largest-frame Largest frame size to use in a ring-group
> passthrough Do not local-ack frames to the specified ring
> ping Establish srb pings
> proxy-netbios-only Proxy explorers only for NetBIOS
> qllc-local-ack Locally terminate QLLC sessions
> remote-peer Specify a remote peer for remote SRB
> ring-group Define a ring group
> sap-80d5 Translate specified SAP frames to 80d5 frames
> sdllc-local-ack Locally terminate SDLC sessions
> tcp-queue-max Maximum TCP queue size for SRB
> transparent Bridging between a transparent and a source-route
> bridge
>
>
>
> -----Original Message-----
> From: Brion Washington
> To: Lupi, Guy; ccielab@groupstudy.com
> Sent: 11/28/2001 4:17 PM
> Subject: RE: Source Route Bridging
>
> Your config is wrong. You need to change source-bridge remote-peer 12
> tcp
> 130.13.5.4 on R4 to source-bridge local-peer peer-id 130.13.5.4, and
> change
> R3 source-bridge remote-peer 12 tcp 130.13.1.1 to source-bridge
> local-peer
> peer-id 130.13.1.1
>
> So basically you are using two remote-peer statements. You can forgo the
> remote-peer one one side if you use Promiscuous at the end of the
> local-peer
> statement.
>
> This should get you working fast.
>
> Brion
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> Lupi, Guy
> Sent: Wednesday, November 28, 2001 1:44 PM
> To: 'ccielab@groupstudy.com'
> Subject: Source Route Bridging
>
>
> Ok, I started out with this elaborate set up, 6 routers, source route
> and
> remote source route bridging, first time trying it. I steadily removed
> routers until I am down to 2 and I still can't get it to work!!! I have
> 2
> routers, each with one token ring interface and one serial interface,
> the
> serial interfaces connect the 2 routers. I looked on CCO, verified that
> everything looks correct, yet I can never get the 2 remote peers to go
> into
> an open state. Below are the configs, an extended ping to show
> connectivity, and the output of a show source from each router. I would
> really appreciate it if someone could take a look and let me know what I
> am
> doing wrong, thanks.
>
>
> R4#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname R4
> !
> !
> ip subnet-zero
> !
> !
> !
> source-bridge ring-group 12
> source-bridge remote-peer 12 tcp 130.13.5.4
> source-bridge remote-peer 12 tcp 130.13.1.1
> !
> !
> interface Serial0
> ip address 4.4.4.4 255.255.255.0
> no ip directed-broadcast
> ip ospf interface-retry 0
> no ip mroute-cache
> no fair-queue
> !
> interface Serial1
> no ip address
> no ip directed-broadcast
> shutdown
> !
> interface TokenRing0
> ip address 130.13.5.4 255.255.255.0
> no ip directed-broadcast
> ip ospf interface-retry 0
> ring-speed 16
> multiring ip
> source-bridge 2 1 12
> source-bridge spanning
> !
> interface BRI0
> no ip address
> no ip directed-broadcast
> shutdown
> !
> router ospf 100
> network 4.4.4.0 0.0.0.255 area 0
> network 130.13.5.0 0.0.0.255 area 0
> !
> ip classless
> !
> !
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> login
> !
> end
>
> R4#
>
> R4#ping
> Protocol [ip]:
> Target IP address: 130.13.1.1
> Repeat count [5]:
> Datagram size [100]:
> Timeout in seconds [2]:
> Extended commands [n]: y
> Source address or interface: 130.13.5.4
> Type of service [0]:
> Set DF bit in IP header? [no]:
> Validate reply data? [no]:
> Data pattern [0xABCD]:
> Loose, Strict, Record, Timestamp, Verbose[none]:
> Sweep range of sizes [n]:
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 130.13.1.1, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms
> R4#
>
>
> R4#sh source
>
> Local Interfaces: receive transmit
> srn bn trn r p s n max hops cnt cnt
> drops
> To0 2 2 12 * b 7 7 7 0 0
> 0
>
> Global RSRB Parameters:
> TCP Queue Length maximum: 100
>
> Ring Group 12:
> This TCP peer: 130.13.5.4
> Maximum output TCP queue length, per peer: 100
> Peers: state bg lv pkts_rx pkts_tx expl_gn
> drops
> TCP
> TCP 130.13.5.4 - 3 0 0 0
> 0
> 0
> TCP 130.13.1.1 closed 3 0 0 0
> 0
> 0
> Rings:
> bn: 2 rn: 2 local ma: 4008.de5c.a38a TokenRing0 fwd:
> 0
>
> Explorers: ------- input ------- ------- output -------
> spanning all-rings total spanning all-rings
> total
> To0 0 0 0 0 0
> 0
>
> Explorer fastswitching enabled
> Local switched: 0 flushed 0 max Bps 38400
>
> rings inputs bursts throttles output
> drops
> To0 0 0 0
> 0
>
> R4#
>
>
>
> R3#sh run
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname R3
> !
> !
> ip subnet-zero
> !
> !
> !
> source-bridge ring-group 12
> source-bridge remote-peer 12 tcp 130.13.1.1
> source-bridge remote-peer 12 tcp 130.13.5.4
> !
> !
> interface Serial0
> ip address 4.4.4.5 255.255.255.0
> no ip directed-broadcast
> ip ospf interface-retry 0
> no ip mroute-cache
> no fair-queue
> clockrate 1300000
> !
> interface Serial1
> no ip address
> no ip directed-broadcast
> shutdown
> !
> interface TokenRing0
> ip address 130.13.1.1 255.255.255.0
> no ip directed-broadcast
> ip ospf interface-retry 0
> ring-speed 16
> multiring ip
> source-bridge 1 1 12
> source-bridge spanning
> !
> interface BRI0
> no ip address
> no ip directed-broadcast
> shutdown
> !
> router ospf 100
> network 4.4.4.0 0.0.0.255 area 0
> network 130.13.1.0 0.0.0.255 area 0
> !
> ip classless
> !
> !
> !
> line con 0
> transport input none
> line aux 0
> line vty 0 4
> login
> !
> end
>
> R3#
>
> R3#ping
> Protocol [ip]:
> Target IP address: 130.13.5.4
> Repeat count [5]:
> Datagram size [100]:
> Timeout in seconds [2]:
> Extended commands [n]: y
> Source address or interface: 130.13.1.1
> Type of service [0]:
> Set DF bit in IP header? [no]:
> Validate reply data? [no]:
> Data pattern [0xABCD]:
> Loose, Strict, Record, Timestamp, Verbose[none]:
> Sweep range of sizes [n]:
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 130.13.5.4, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 4/9/28 ms
> R3#
>
> R3#sh sour
>
> Local Interfaces: receive transmit
> srn bn trn r p s n max hops cnt cnt
> drops
> To0 1 1 12 * f 7 7 7 0 0
> 0
>
> Global RSRB Parameters:
> TCP Queue Length maximum: 100
>
> Ring Group 12:
> This TCP peer: 130.13.1.1
> Maximum output TCP queue length, per peer: 100
> Peers: state bg lv pkts_rx pkts_tx expl_gn
> drops
> TCP
> TCP 130.13.1.1 - 3 0 0 0
> 0
> 0
> TCP 130.13.5.4 closed 3 0 0 0
> 0
> 0
> Rings:
> bn: 1 rn: 1 local ma: 4008.de6c.6382 TokenRing0 fwd:
> 0
>
> Explorers: ------- input ------- ------- output -------
> spanning all-rings total spanning all-rings
> total
> To0 0 0 0 0 0
> 0
>
> Explorer fastswitching enabled
> Local switched: 0 flushed 0 max Bps 38400
>
> rings inputs bursts throttles output
> drops
> To0 0 0 0
> 0
>
> R3#
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:24 GMT-3