From: fwells12 (fwells12@xxxxxxxxxxx)
Date: Tue Nov 20 2001 - 16:01:27 GMT-3
My apologies Andy. With my very limited hands on experience with voice I
thought a specific destination number on the dial peer was the only one you
could use to call it.
I wish I had a voice lab!!!!!!!!
----- Original Message -----
From: "Andy Cuberly" <andyc@netcat.com>
To: "fwells12" <fwells12@hotmail.com>
Sent: Tuesday, November 20, 2001 10:58 AM
Subject: RE: Can someone verify this voice config please.
> Before commenting back that my solutions are wrong please research the
> proper configurations for voice and get some hands on, I am not guessing
> that this configuration works, I know that it does. If you are sure that
> your configs are correct then why ask for help?
>
> Andy Cuberly
> Network Engineer
> CCIE #8386
> office (949) 852-6660
> mobile (949) 278-0226
>
> -----Original Message-----
> From: fwells12 [mailto:fwells12@hotmail.com]
> Sent: Tuesday, November 20, 2001 10:16 AM
> To: Andy Cuberly; ccielab@groupstudy.com
> Subject: Re: Can someone verify this voice config please.
>
>
> Thanks for the reply. Your suggestions don't meet the requirements
though.
> To dial the peer you could only use 111. I want to be able to dial it
using
> any number of any length...if it can be done.
>
> ----- Original Message -----
> From: "Andy Cuberly" <andyc@netcat.com>
> To: "'fwells12'" <fwells12@hotmail.com>; <ccielab@groupstudy.com>
> Sent: Tuesday, November 20, 2001 5:59 AM
> Subject: RE: Can someone verify this voice config please.
>
>
> > Almost there - You need to insert a single "." before the capital "T" in
> the
> > destination pattern in the VOIP dial peer.
> >
> > Looks like this:
> >
> > destination-pattern .T
> >
> > Also - You need to add a valid extension number in the Pots dial peer on
> the
> > destination pattern line.
> >
> > example:
> >
> > R1
> > dial-peer voice 1 pots
> > destination-pattern 111
> > port 1/0/0
> >
> > dial-peer voice 2 voip
> > destination-pattern .T
> > session target ipv4:x.x.x.x (IP address of R2)
> >
> >
> > The rest looks good.
> >
> > Andy Cuberly
> > CCIE #8386
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > fwells12
> > Sent: Tuesday, November 20, 2001 12:50 AM
> > To: ccielab@groupstudy.com
> > Subject: Can someone verify this voice config please.
> >
> >
> > I don't have voice access to try this. The object of the excersize is
to
> be
> > able to use any number to dial over frame-relay to another phone and
have
> > that
> > phone be able to dial back using any number too.
> >
> >
> > R1-----------frame-relay ------------R2
> >
> > R1
> > dial-peer voice 1 pots
> > destination-pattern T
> > port 1/0/0
> >
> > dial-peer voice 2 voip
> > destination-pattern T
> > session target ipv4:x.x.x.x
> >
> > R2
> > dial-peer voice 1 pots
> > destination-pattern T
> > port 1/0/0
> >
> > dial-peer voice 2 voip
> > destination-pattern T
> > session target ipv4:x.x.x.x
This archive was generated by hypermail 2.1.4 : Fri Jun 21 2002 - 06:45:19 GMT-3