From: Jay Hennigan (jay@xxxxxxxx)
Date: Thu Sep 13 2001 - 13:16:01 GMT-3
On Thu, 13 Sep 2001, Ahmed Mamoor wrote:
> I have 3 routers with same problem can anyone help....
>
>
> Problem:
> Not getting any type of data from my 2501 router's console or AUX port.
>
> observation:
> 1- When I power up the router Its goes apparently normal through the booting
> process and after 30 sec. Light the GREEN OK light on the back of the
> router.
> 2- When I attach WAN serial cable with my 2502 router with other one (2501 &
> 2503) after some sec the data is been send through the WAN serial cable as
> these routers are sending keep alive packets to each other.
> 3- When I place a RS232 tester in between the router's console and the
> computer serial port it gives all the signal except the Rx signal from the
> router.
This indicates a *possible* hardware failure in the router, but the same
issue with three of them makes this unlikely.
I would try the following:
* With only the console port and the RS-232 tester connected (unplug from
the PC), do you get any light on either the TXD or RXD indicator? And,
when you power up the router and it goes through the boot sequence, does
this light flicker? If so, it sounds like a rollover cable or hood
problem.
* Substitute a different rollover cable. You're aware that the rollover
console cable is a flat ribbon cable, and is pinned differently than
an ethernet jumper? They are usually light blue in color, although
Cisco sometimes supplies green ones (with terminal servers) and black
ones (for the AUX port). The color doesn't matter, they're all wired
the same but different from an ethernet jumper. See:
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis2500/2509/a
csvrug/cables.htm#xtocid402311
* Substitute a different hood. The pinning on yours may be wrong.
* Verify that flow control is set to "none" in your terminal program.
* Get an RJ-45 type (8-pin) jack. Wire pins 3 and 6 together. Plug
your PC, hood, and rollover cable into this in place of the router.
Type on the screen and see if your characters echo. Then unplug the
jack and verify that they stop echoing. This tests your PC, hood,
and cable.
* If you have two 9-pin hoods and two computers, you should be able to
connect them together using a rollover cable, run a terminal program
on both, and what you type on one should display on the screen of the
other.
> 4- Console port is giving nothing but AUX port give a ASCII character when
> power ups and nothing.
> Solution Implemented and tested:
> 1- I check the router for every BAUD rate but no help.
> 2- I thought the routers power supply is not giving sufficient power to
> router, I changed it with my other router's power supply but no help.
> 3- I changed FLASH and DRAM but nothing happened.
> 4- I changed the computers console cable with the original one and changed
> computer too but no help.
> 5- I reset the routes jumper found just aside with ROM, thinking that IOS is
> corrupted but nothing happened.
>
> I am sure my router is not completely dead as it is giving packets through it
s
> WAN interfaces when connected to other router. Any suggestion will be a great
> help for me.
It sounds like a low-level physical problem to me.
-- Jay Hennigan - CCIE #7880 - Network Administration - jay@west.net NetLojix Communications, Inc. - http://www.netlojix.com/ WestNet: Connecting you to the planet. 805 884-6323 **Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:32:16 GMT-3