From: SFeldberg@xxxxxxxxxxxxx
Date: Fri Aug 17 2001 - 12:01:57 GMT-3
Do you see the link become active on the transceiver? If not, that would
point to the Catalyst. Have you tried turning off autonegotiation or
manually setting the Cat port to 10mbps/half?
Check your ribbon cables. They tend to get damaged, pins bent on
connectors, etc. Your MCI card shoud have two connectors for ethernet, is
E1 in use? Does it work? If not in use, have you tried moving the ribbon
cable over to it and testing on E1?
HTH,
Steve
"Tony Dubiel"
<tdubiel@bellatl To:
antic.net> cc:
Sent by: Subject: AGS +
nobody@groupstud
y.com
08/17/2001 09:29
AM
Please respond
to "Tony Dubiel"
Hello,
I'm using an AGS + router for a Frame Switch. I was able to set up the
Frame
Relay and Token Ring, but
am having difficulty getting my Ethernet up. I'm using a transceiver (AUI
to
RJ 45) to connect to a Cat 5000.
In fact I tried two different transceivers.
I've also tried a cross-over to a PC but with no success. I also opened up
the
AGS and verified the Ethernet appliqui
was connected to the MCI Controller card.
My question here is, since I had to modify jumper settings to allow my
serial
interfaces to be DCE and generate timing, Do
I also need to change some setting to allow my Ethernet to work.
I'm pretty sure Ethernet is just supposed to come up if there is a Link
detected because it send the keepalives to itself.
I turn off keep-alives and I can't ping anything on that VLAN from the AGS
+
but the line protocol comes up.
Has anyone else had trouble with an AGS+ and Ethernet?
Ethernet0 is up, line protocol is down
Hardware is MCI Ethernet, address is 0000.0c03.ba71 (bia 0000.0c03.ba71)
Description: Backup
Internet address is 10.3.1.1 255.255.255.0
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output 0:00:02, output hang never
Last clearing of "show interface" counters never
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
5184 packets output, 313001 bytes, 0 underruns
0 output errors, 0 collisions, 5083 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
OS (tm) GS Software (GS3-K-M), Version 10.3(13), RELEASE SOFTWARE (fc2)
interface Ethernet0
description Backup
ip address 10.3.1.1 255.255.255.0
Probably the card is bad because this box is old as dirt.
Tony
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:52 GMT-3