From: Maness, Drew (drew.maness@xxxxxxxxxxxx)
Date: Wed May 09 2001 - 19:52:28 GMT-3
Pete,
I can feel your pain. Could there be something wrong with your TFTP server?
The only thing I noticed that is kind of out of wack is after you copy the
file, you get:
OK - 4319328/8388608 bytes]
the enterprise version of the 11.2.26 is 8mg. You are only copying a
little over 4. I would think that there is either something wrong with your
tftp server or the file is corrupted.
I know not much of a help but...
Let me know how it works out, this is a good who-dun'it
-----Original Message-----
From: Pete Kowalsky [mailto:pkowalsky@evolvesoft.com]
Sent: Wednesday, May 09, 2001 3:20 PM
To: ccielab@groupstudy.com
Subject: Re: IOS 11.2, Enterprise on 2502 -- SERIOUS headaches!
Here's the EXACT type of errors I get. The image checksum appears to be
fine, but for some reason the router cannot read it from the flash once it
reloads. You can see that the last line is when I get dumped to ROM boot
mode. My router is stoned.
Thanks,
Pete
Zermatt#cop tf fl
**** NOTICE ****
Flash load helper v1.0
This process will accept the copy options and then terminate
the current system image to use the ROM based image for the copy.
Routing functionality will not be available during that time.
If you are logged in via telnet, this connection will terminate.
Users with console access can see the results of the copy operation.
---- ******** ----
Proceed? [confirm]y
System flash directory:
File Length Name/status
1 6447604 c2500-d-l.113-11a.T1.bin
[6447668 bytes used, 1940940 available, 8388608 total]
Address or name of remote host [10.21.11.113]?
Source file name? c2500-i-l.112-26.bin
Destination file name [c2500-i-l.112-26.bin]?
Accessing file 'c2500-i-l.112-26.bin' on 10.21.11.113...
Loading c2500-i-l.112-26.bin from 10.21.11.113 (via Serial0): ! [OK]
Erase flash device before writing? [confirm]y
Flash contains files. Are you sure you want to erase? [confirm]y
%Warning: File not a valid executable for this system
Copy file? [confirm]y
System configuration has been modified. Save? [yes/no]: y
Building configuration...
[OK]
Copy 'c2500-i-l.112-26.bin' from server
as 'c2500-i-l.112-26.bin' into Flash WITH erase? [yes/no]y
%SYS-4-CONFIG_NEWER: Configurations from version 11.3 may not be correctly
understood.
%FLH: c2500-i-l.112-26.bin from 10.21.11.113 to flash ...
System flash directory:
File Length Name/status
1 6447604 c2500-d-l.113-11a.T1.bin
[6447668 bytes used, 1940940 available, 8388608 total]
Accessing file 'c2500-i-l.112-26.bin' on 10.21.11.113...
Loading c2500-i-l.112-26.bin from 10.21.11.113 (via Serial0): ! [OK]
%Warning: File not a valid executable for this system
Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased
Loading c2500-i-l.112-26.bin from 10.21.11.113 (via Serial0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!
[OK - 4319328/8388608 bytes]
Verifying checksum... OK (0x70C6)
Flash copy took 0:01:54 [hh:mm:ss]
%FLH: Re-booting system after downloadFlash boot: No bootable files found in
flash.
File boot failed -- File not accessible
...*** BOOTING ROM IMAGE ***
System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-1998 by cisco Systems
2500 processor with 4096 Kbytes of main memory
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB2,
PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 05-Oct-98 10:52 by jaturner
Image text-base: 0x01010000, data-base: 0x00001000
cisco 2500 (68030) processor (revision D) with 4096K/2048K bytes of memory.
Processor board ID 01777901, with hardware revision 00000000
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Token Ring/IEEE 802.5 interface.
2 Serial network interfaces.
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Press RETURN to get started!
Zermatt(boot)#
----- Original Message -----
From: "Pete Kowalsky" <pkowalsky@evolvesoft.com>
To: "Scott Young" <syoung@pei.com>; <ccielab@groupstudy.com>
Sent: Wednesday, May 09, 2001 5:59 PM
Subject: Re: IOS 11.2, Enterprise on 2502 -- SERIOUS headaches!
> Nope -- regular ugly grey chassis. Thanks for the reply! I remember the
> AccessPro/CiscoPro stuff you're talking about, and this is definitely not
> one of those... Still trying to figure this thing out... Here's my boot
> rom info, and it takes the IOS 11.3 IP-only image just fine (you can see
> that's what's running now):
>
>
> Zermatt#sh ve
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-D-L), Version 11.3(11a)T1, RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Fri 24-Sep-99 00:18 by pwade
> Image text-base: 0x03034F74, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE
> SOFTWARE (fc1)
> BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB2,
> PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
>
> Zermatt uptime is 14 minutes
> System restarted by reload
> System image file is "flash:c2500-d-l.113-11a.T1.bin", booted via flash
>
> cisco 2500 (68030) processor (revision D) with 4096K/2048K bytes of
memory.
> Processor board ID 01777901, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> 1 Token Ring/IEEE 802.5 interface(s)
> 2 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
>
> Configuration register is 0x2102
>
> Zermatt#
>
> Thanks,
> Pete
>
>
> ----- Original Message -----
> From: "Scott Young" <syoung@pei.com>
> To: "'Pete Kowalsky'" <pkowalsky@evolvesoft.com>; <ccielab@groupstudy.com>
> Sent: Wednesday, May 09, 2001 5:35 PM
> Subject: RE: IOS 11.2, Enterprise on 2502 -- SERIOUS headaches!
>
>
> > The router doesn't care about the name of the file.
> >
> > Is your 2502 a Cisco Pro? If it is and has not had the one-time
software
> > upgrade, then it will not accept a 2500 IOS. Most of the Pros had a
white
> > chassis. Since I upgraded mine a while back, I don't remember if
there's
> a
> > message at boot-up stating that it's a Pro.
> >
> > Just a thought.
> >
> > SY
> >
> > -----Original Message-----
> > From: louie kouncar [mailto:lkouncar@UU.NET]
> > Sent: Wednesday, May 09, 2001 3:25 PM
> > To: 'Pete Kowalsky'; ccielab@groupstudy.com
> > Subject: RE: IOS 11.2, Enterprise on 2502 -- SERIOUS headaches!
> >
> >
> > Well,
> >
> > Have you tried to copy the name as it is "c2500-js-l.112-26.bin" when
you
> > are asked to enter the source file name? You are typing
"cisco3-2500.bin"
> > and I think that with the naming convention used by Cisco it does not
see
> > this as a valid IOS.
> > I don't have access to a router at this moment to test this but I think
> you
> > should give it a try......
> >
> >
> > Thanks
> >
> >
> >
> > Louie J. Kouncar
> > TCO3 Senior Data Center Engineer
> > UUNET
> > W-703-343-6645
> > C-703-304-2460
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Pete Kowalsky
> > Sent: Wednesday, May 09, 2001 4:33 PM
> > To: ccielab@groupstudy.com
> > Subject: IOS 11.2, Enterprise on 2502 -- SERIOUS headaches!
> >
> >
> > Gang,
> >
> > I'm about ready to throw one of my 2502's out the freakin window
here.
> > I'm having a problem with successfully loading ANY 11.2 image from
flash.
> I
> > get the errors as shown below EVERY time I copy an 11.2 image. My goal
is
> > to get an enterprise image into 8MB flash and 6MB RAM. According to the
> > hardware compatibility matrix and the IOS Upgrade Planner on CCO, this
can
> > be done with 'c2500-js-l.112-26.bin', which appears to be the latest
11.2
> > release for this platform. For some reason, I keep getting this
> "%Warning:
> > File not a valid executable for this system" error, and if I go ahead
and
> > copy the file, the boot rom (11.0) comes back and says "Running default
> > software" after it reloads, and never reads the 11.2 image from flash.
I
> am
> > NOT compressing the image. The image is smaller than the flash. The
> image
> > requires 6MB, and I have 6 MB. The config register is 0x2102. I can
even
> > do a TFTP boot from ROM monitor, and it does not load the 11.2 image. I
> > can't figure this out. I've tried erasing the flash, reloading, then
> > copying the file, and that makes no difference. When I do that, I get
> this:
> >
> >
> > Abort at 0x10B7CAC (PC)
> > >b c2500-js-l.112-21.bin 10.21.11.113
> >
> > %SCHED-2-WATCH: Attempt to set uninitialized watched boolean (address
0).
> > -Process= "*Init*", ipl= 7
> > -Traceback= 10EB47E 1110E52
> > Exception: Illegal Instruction at 0x0 (PC)
> >
> > System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE
SOFTWARE
> > (fc1)
> > Copyright (c) 1986-1998 by cisco Systems
> > 2500 processor with 4096 Kbytes of main memory
> >
> >
> > The rest of the time, I just get crap like the following. Can anyone
out
> > there gimme some advice? (Advice other than, "hey loser, upgrade the
DRAM
> > flash in your router and load 12.x!") Thanks a million!
> >
> >
> > Cisco Internetwork Operating System Software
> > IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB2,
> > PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
> > Copyright (c) 1986-1996 by cisco Systems, Inc.
> > Compiled Mon 05-Oct-98 10:52 by jaturner
> > Image text-base: 0x01010000, data-base: 0x00001000
> >
> > ROM: System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE
> > SOFTWARE (fc1)
> >
> > Zermatt uptime is 17 minutes
> > System restarted by power-on
> > Running default software
> >
> > cisco 2500 (68030) processor (revision D) with 4096K/2048K bytes of
> memory.
> > Processor board ID 01777901, with hardware revision 00000000
> > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> > 1 Token Ring/IEEE 802.5 interface.
> > 2 Serial network interfaces.
> > 32K bytes of non-volatile configuration memory.
> > 8192K bytes of processor board System flash (Read/Write)
> >
> > Configuration register is 0x2142 (will be 0x2102 at next reload)
> >
> > Zermatt(boot)#cop tf fl
> >
> > System flash directory:
> > No files in System flash
> > [0 bytes used, 8388608 available, 8388608 total]
> > Address or name of remote host [10.21.11.113]?
> > Source file name? igs-j-l.111-24a.bin
> > Destination file name [igs-j-l.111-24a.bin]?
> > Accessing file 'igs-j-l.111-24a.bin' on 10.21.11.113...
> > Loading igs-j-l.111-24a.bin from 10.21.11.113 (via Serial0): ! [OK]
> >
> > Erase flash device before writing? [confirm]n
> > %Warning: File not a valid executable for this system
> > Copy file? [confirm]n
> > Zermatt(boot)#cop tf fl
> >
> > System flash directory:
> > No files in System flash
> > [0 bytes used, 8388608 available, 8388608 total]
> > Address or name of remote host [10.21.11.113]?
> > Source file name? cisco3-2500.bin
> > Destination file name [cisco3-2500.bin]?
> > Accessing file 'cisco3-2500.bin' on 10.21.11.113...
> > Loading cisco3-2500.bin from 10.21.11.113 (via Serial0): ! [OK]
> >
> > Erase flash device before writing? [confirm]n
> > %Warning: File not a valid executable for this system
> > Copy file? [confirm]n
> > Zermatt(boot)#
> > **Please read:http://www.groupstudy.com/list/posting.html
> > **Please read:http://www.groupstudy.com/list/posting.html
> > **********************************************************************
> > This email and any files transmitted with it are confidential and
> > intended solely for the use of the individual or entity to whom they
> > are addressed. If you have received this email in error please notify
> > the system manager.
> >
> > This footnote also confirms that this email message has been swept by
> > MIMEsweeper for the presence of computer viruses.
> >
> > www.mimesweeper.com
> > **********************************************************************
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:37 GMT-3