RE: telnet -> telnet -> telnet

From: andrew.2.shore@xxxxxx
Date: Fri May 04 2001 - 04:28:53 GMT-3

• Next message: Vincent Lee: "Loading cfg messages"
• Previous message: andrew.2.shore@xxxxxx: "RE: Good IpSec/IKE book"
• Maybe in reply to: andrew.2.shore@xxxxxx: "telnet -> telnet -> telnet"
• Next in thread: Gonzales, Enrique: "RE: telnet -> telnet -> telnet"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

   
Guys

thanks for all the replies !

The CNTR SHIFT 6 CNTR SHIFT 6 X is the easy way :)

Thanks again

Andrew Shore
BTcd
Information Systems Engineering
Internet & Multimedia

-----Original Message-----
From: ShahzaD Ali [mailto:shahzad-ali@home.com]
Sent: 03 May 2001 21:38
To: Mas Kato; andrew.2.shore; ccielab
Subject: RE: telnet -> telnet -> telnet

Try this

r3#terminal escape-character 16
"^P" is the escape character
r3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r3(config)#line vty 0 4
r3(config-line)#escape-character 16
r3(config-line)#
r3#140.1.1.1
Trying 140.1.1.1 ... Open

User Access Verification

Password:
r1>en
Password:
r1# --------- ctrl 6 + x you will back to r3
r3#

Regards,

ShahzaD

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Mas Kato
Sent: Thursday, May 03, 2001 3:00 AM
To: andrew.2.shore@bt.com; ccielab@groupstudy.com
Subject: RE: telnet -> telnet -> telnet

Andrew,

I haven't thought this completely through, but I wonder if you can
re-define the telnet escape sequence on one router or the other (R1 or
R2)?

Regards,

Mas Kato

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
andrew.2.shore@bt.com
Sent: Thursday, May 03, 2001 12:46 AM
To: ccielab@groupstudy.com
Subject: telnet -> telnet -> telnet

Gang

R1 ----> R2 ----> R3

If I have three routers and telnet from R1 to R2 then reverse telnet to
R3
is there a way to get back to R2. For security reasons it is not
possible to
telnet directly to R2.

CNTR Shift 6 X takes me back to R1 !

I have a real world situation where I need to use R2 (terminal server)
to do
config work on 48 new devices and just flicking between them would make
life
so much easier.

Thanks,

Andrew Shore
BTcd
Information Systems Engineering
Internet & Multimedia
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html

• Next message: Vincent Lee: "Loading cfg messages"
• Previous message: andrew.2.shore@xxxxxx: "RE: Good IpSec/IKE book"
• Maybe in reply to: andrew.2.shore@xxxxxx: "telnet -> telnet -> telnet"
• Next in thread: Gonzales, Enrique: "RE: telnet -> telnet -> telnet"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:33 GMT-3