From: BUI, TIN T (SBCSI) (tb4565@xxxxxxx)
Date: Mon Jan 08 2001 - 19:52:01 GMT-3
Try www.dice.com or www.ccprep.com
> Tin T. Bui
> Senior Network Manager
> Network Management Center
> SBC Services Inc.
> 7337 Trade Street, Rm 1110
> San Diego, Ca 92121
> Office #: 858-886-4644/858-886-4589
> Pager #: 858-494-0482
> Fax #: 858-549-4103
> Email: tb4565@sbc.com
>
-----Original Message-----
From: Bernard Dunn [mailto:dunn@cisco.com]
Sent: Saturday, January 06, 2001 5:40 AM
To: Dezhong Cai
Cc: ccielab@groupstudy.com
Subject: Re: jobs for CCIE
They're more than welcome to apply any jobs.. :^)
On Fri, 5 Jan 2001, Dezhong Cai wrote:
> Hi,
>
> Is there any web site for CCIE to find a job?
>
> Dezhong
>
> ----- Original Message -----
> From: "perez claude-vincent" <claude_vincent@yahoo.com>
> To: "Bernard Dunn" <dunn@cisco.com>
> Cc: "'Ccielab" <ccielab@groupstudy.com>
> Sent: Friday, January 05, 2001 9:28 PM
> Subject: Re: dialer map. hub and spoke issues!
>
>
> > Thank you all for your advises. It's working now normally.
> >
> > Vincent
> >
> > Bernard Dunn <dunn@cisco.com> wrote:
> > Clude,
> >
> > Your interface dialer1 doesn't have an authentication method, so it's
> > matching on caller ID.
> >
> > Might want to just add 'ppp authen chap pap' or something..
> >
> > Regards
> >
> > Bernard.
> >
> >
> > On Fri, 5 Jan 2001, Claude-Vincent wrote:
> >
> > > Dear All,
> > >
> > > I have a problem with my dialer interfaces. the ios version is
11.2(18)
> of
> > > the Hub router 2500series.
> > >
> > > It is a Hub and spokes topology. I would like to ping R1 and R2 from
the
> hub
> > > using an ISDN line. Please fing hereby the conf. + debug.
> > >
> > > If I add dialer pool-member 2 on the bri int. I can ping R2 but not
R1.
> If I
> > > modify on the dialer2, dialer pool 1, same. Moreover, what I don't
> > > understand is why after the outgoing call has been established on the
> first
> > > B channel, I receive automatically a incoming call from unknown unless
I
> > > remove the "dialer pool-member 2" of the bri interface!
> > >
> > > I don't want to use static dialer map.
> > >
> > > Please help me. I run out of ideas!!!!
> > >
> > > interface BRI0
> > > no ip address
> > > no ip redirects
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > keepalive 300
> > > dialer pool-member 1
> > > no fair-queue
> > > no cdp enable
> > > ppp authentication pap chap
> > > !
> > > interface Dialer1
> > > ip address 192.168.4.65 255.255.255.252
> > > ip access-group 11 in
> > > ip access-group 11 out
> > > no ip redirects
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > no ip split-horizon
> > > no ip mroute-cache
> > > dialer remote-name R1
> > > dialer idle-timeout 90
> > > dialer string ###
> > > dialer pool 1
> > > dialer-group 1
> > > no fair-queue
> > > no cdp enable
> > > ppp pap sent-username ### password ###
> > > !
> > > interface Dialer2
> > > ip address 10.65.4.65 255.255.255.0
> > > ip access-group 11 in
> > > ip access-group 11 out
> > > encapsulation ppp
> > > dialer remote-name R2
> > > dialer idle-timeout 90
> > > dialer string ###
> > > dialer pool 2
> > > dialer-group 1
> > > ppp authentication chap
> > >
> > > ISDN BR0: RX <- SETUP pd = 8 callref = 0x21
> > > Bearer Capability i = 0x8890
> > > Channel ID i = 0x8A
> > > Display i = 'LONG DISTANCE'
> > > Calling Party Number i = 0x00C3
> > > ISDN BR0: Incoming call id = 0x26B
> > > ISDN BR0: received HOST_INCOMING_CALL
> > > ISDN BR0: Event: Received a call from on B2 at 64 Kb/s
> > > ISDN BR0: Event: Accepting the call
> > > %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> > > ISDN BR0: TX -> CONNECT pd = 8 callref = 0xA1
> > > ISDN BR0: RX <- CONNECT_ACK pd = 8 callref = 0x21
> > > ISDN BR0: Event: Hangup call to call id 0x26B
> > > %ISDN-6-DISCONNECT: Interface BRI0:2 disconnected from ###, call
lasted
> 1
> > > sec
> > > onds
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:24 GMT-3