From: Dezhong Cai (dcai@xxxxxxxxx)
Date: Sat Jan 06 2001 - 03:52:31 GMT-3
Hi,
Is there any web site for CCIE to find a job?
Dezhong
----- Original Message -----
From: "perez claude-vincent" <claude_vincent@yahoo.com>
To: "Bernard Dunn" <dunn@cisco.com>
Cc: "'Ccielab" <ccielab@groupstudy.com>
Sent: Friday, January 05, 2001 9:28 PM
Subject: Re: dialer map. hub and spoke issues!
> Thank you all for your advises. It's working now normally.
>
> Vincent
>
> Bernard Dunn <dunn@cisco.com> wrote:
> Clude,
>
> Your interface dialer1 doesn't have an authentication method, so it's
> matching on caller ID.
>
> Might want to just add 'ppp authen chap pap' or something..
>
> Regards
>
> Bernard.
>
>
> On Fri, 5 Jan 2001, Claude-Vincent wrote:
>
> > Dear All,
> >
> > I have a problem with my dialer interfaces. the ios version is 11.2(18)
of
> > the Hub router 2500series.
> >
> > It is a Hub and spokes topology. I would like to ping R1 and R2 from the
hub
> > using an ISDN line. Please fing hereby the conf. + debug.
> >
> > If I add dialer pool-member 2 on the bri int. I can ping R2 but not R1.
If I
> > modify on the dialer2, dialer pool 1, same. Moreover, what I don't
> > understand is why after the outgoing call has been established on the
first
> > B channel, I receive automatically a incoming call from unknown unless I
> > remove the "dialer pool-member 2" of the bri interface!
> >
> > I don't want to use static dialer map.
> >
> > Please help me. I run out of ideas!!!!
> >
> > interface BRI0
> > no ip address
> > no ip redirects
> > no ip directed-broadcast
> > encapsulation ppp
> > keepalive 300
> > dialer pool-member 1
> > no fair-queue
> > no cdp enable
> > ppp authentication pap chap
> > !
> > interface Dialer1
> > ip address 192.168.4.65 255.255.255.252
> > ip access-group 11 in
> > ip access-group 11 out
> > no ip redirects
> > no ip directed-broadcast
> > encapsulation ppp
> > no ip split-horizon
> > no ip mroute-cache
> > dialer remote-name R1
> > dialer idle-timeout 90
> > dialer string ###
> > dialer pool 1
> > dialer-group 1
> > no fair-queue
> > no cdp enable
> > ppp pap sent-username ### password ###
> > !
> > interface Dialer2
> > ip address 10.65.4.65 255.255.255.0
> > ip access-group 11 in
> > ip access-group 11 out
> > encapsulation ppp
> > dialer remote-name R2
> > dialer idle-timeout 90
> > dialer string ###
> > dialer pool 2
> > dialer-group 1
> > ppp authentication chap
> >
> > ISDN BR0: RX <- SETUP pd = 8 callref = 0x21
> > Bearer Capability i = 0x8890
> > Channel ID i = 0x8A
> > Display i = 'LONG DISTANCE'
> > Calling Party Number i = 0x00C3
> > ISDN BR0: Incoming call id = 0x26B
> > ISDN BR0: received HOST_INCOMING_CALL
> > ISDN BR0: Event: Received a call from on B2 at 64 Kb/s
> > ISDN BR0: Event: Accepting the call
> > %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> > ISDN BR0: TX -> CONNECT pd = 8 callref = 0xA1
> > ISDN BR0: RX <- CONNECT_ACK pd = 8 callref = 0x21
> > ISDN BR0: Event: Hangup call to call id 0x26B
> > %ISDN-6-DISCONNECT: Interface BRI0:2 disconnected from ###, call lasted
1
> > sec
> > onds
> >
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:27:23 GMT-3