From: MAZHAR KARAGULLE (mkaragulle@xxxxxxxxxxxxxxxxxx)
Date: Wed Dec 06 2000 - 04:40:15 GMT-3
Yes,
x.x.x.x in frame-relay map statement means the IP address of the new
router.
Bye
Gönderilen:
Bilgisine:
"zhangxianqi" "Mazhar" <mkaragulle@tekstilbank.com.tr>,
<xianqizhang@sina.com> <jr_chen@ringline.com.tw>, <lserrano@ipt.es>,
"zhang zhichao" <zhichao@yahoo.com>
06/12/2000 05:58 AM Konu:
Re: Rép. : autoinstall through framerelay
hi, Mazhar
I guess the ip add x.x.x is different with the ip add "frame-relay map ip
x.x.x.x YYYY broadcast
".
James,make sure your pvc 100 is fine.your config is allright.
xianqi
----- Original Message -----
From: MAZHAR KARAGULLE <mkaragulle@tekstilbank.com.tr>
To: <>
Cc: <ccielab@groupstudy.com>; <lserrano@ipt.es>; <tmartin@ares.fr>;
<zhangxqi@gitc.com.cn>; <zhichao@yahoo.com>
Sent: Tuesday, December 05, 2000 11:58 PM
Subject: Re: Rép. : autoinstall through framerelay
Hi,
Existing router configuration requires only
ip address x.x.x. ....
encapsulation frame-relay
frame-relay map ip x.x.x.x YYYY broadcast
ip helper-address Z.Z.Z.Z
Newrouter side FR-SW requires
frame-relay lmi-type cisco
&
only one DLCI should be connected to new router.
I hope this helps you
Bye
Gönderilen: LUIS SERRANO
SERRANO <lserrano@ipt.es>
Bilgisine:
James Chen tmartin@ares.fr, zhangxqi@gitc.com.cn,
<jr_chen@ringline.com.tw> ccielab@groupstudy.com,
mkaragulle@tekstilbank.com.tr,
05/12/2000 05:45 PM zhichao@yahoo.com
Konu:
Lütfen jr_chen adresine Re: Rép. : autoinstall through framerelay
yanýtlayýnýz.
Hello, Sir:
I can not get the ip in newrouter from autoinstall....
my config is
existing router:
int s0/0
encap frame-relay
ip add 10.10.10.1 255.255.255.0
frame lmi-type cisco
frame map ip 10.10.10.2 100 broadcast CISCO
ip helper-address 210.59.251.236
but when I debug ip packet ,
no any packet come from newrouter to try to get config ?
I have done the autoinstall when I use hdlc encapulation successfully.
but can't with frame-relay ?
what do I miss ?
Thaks for your answer !!!
James
LUIS SERRANO SERRANO wrote:
> Hi all,
> It is the first time that i write a e-mail to groupstudy group.
> Last week i get the CCIE number # 6503 at Brussels.
> I think this mailing list has been very, very useful for me.
>
> About autoinstall, i have tested whitout broadcast parameter in frame
relay map command and they works also. In this test i have the ip helper
address command enabled to the TFTP server's IP address.
>
> Regards
>
> >>> "Thierry MARTIN" <tmartin@ares.fr> 11/29 4:37 p.m. >>>
> Hello,
>
> for autoinstall with frame relay, you must use :
>
> - LMI cisco (default)
> - encap cisco (default)
> - only one DLCI for this destination
> - broadcast => frame-relay map ip 10.0.1.2 100 broadcast
> - address ".1 " for central router
> - address ".2" will be assign to the autoinstall router
>
> Other IP address don't run.
>
> Autoinstall don't run with VLSM
>
> A+
> thierry
> CCNA, CCDA, CCNP, specialization ATM
> Lab for February
>
>
*******************************************************************************
******************************
>
> Cordialement
>
> \\\\///
> (/ @ @ /)
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:59 GMT-3