From: Shaun Nicholson (Shaun.Nicholson@xxxxxx)
Date: Fri Dec 01 2000 - 12:43:30 GMT-3
Try using the no peer neighbor-route under the bri0 interface on both side and
let the group know if it works.
Shaun
jr_chen@ringline.com.tw on 12/01/2000 10:36:00 AM
To: ccielab@groupstudy.com@Internet
cc: (bcc: Shaun Nicholson/MD/KAIPERM)
Subject: Re: [Q]OSPF Demand-Circuit over ISDN DDR
After I modify the config to remove the "ip ospf network non-broadcast" and
"neighbor" command, the condition is the same . the hello is continuous to
receive.
and the neighbor relation can not be established..
---------------------------------------------------------------
R3#sh ip ospf nei
Neighbor ID Pri State Dead Time Address Interface
137.1.6.6 1 FULL/DR 00:00:35 137.1.63.6
FastEthernet0/
0
137.1.4.4 1 FULL/ - 00:01:42 137.1.254.4 Serial0/0
137.1.2.2 1 FULL/ - 00:01:34 137.1.254.2 Serial0/0
137.1.5.5 1 INIT/ - 00:00:34 137.1.35.2 BRI0/0
R3#sh ip ospf int bri0/0
BRI0/0 is up, line protocol is up (spoofing)
Internet Address 137.1.35.1/30, Area 3
Process ID 1, Router ID 137.1.3.3, Network Type POINT_TO_POINT, Cost: 1562
Run as demand circuit.
DoNotAge LSA allowed.
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:05
Index 1/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 0, maximum is 0
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 0
Suppress hello for 1 neighbor(s)
R5#sh ip ospf nei
Neighbor ID Pri State Dead Time Address Interface
137.1.6.6 1 FULL/DR 00:00:32 137.1.65.6
FastEthernet0/
0
R5#sh ip ospf int bri0/0
BRI0/0 is up, line protocol is up (spoofing)
Internet Address 137.1.35.2/30, Area 3
Process ID 1, Router ID 137.1.5.5, Network Type POINT_TO_POINT, Cost: 1562
Configured as demand circuit.
Run as demand circuit.
DoNotAge LSA allowed.
Transmit Delay is 1 sec, State DOWN,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
------------------------------------------------------------------------------
I even can not see the neighbor in the ospf neighbor table ?
why ?
Is there anything I missed ?
PS. I don't have any rip or eigrp config in R3 and R5. so with no any
redistribution .
James
James Chen wrote:
> Hello, Sir:
>
> I have big problem with OSPF Demand-Circuits.
> My config is as following:
> -----------------------------------------------------------
> R3:
> interface BRI0/0
> ip address 137.1.35.1 255.255.255.252
> no ip directed-broadcast
> encapsulation ppp
> ip ospf network non-broadcast
> dialer map ip 137.1.35.2 name R5
> dialer-group 1
> isdn switch-type basic-5ess
> ppp quality 90
> ppp authentication pap
> ppp pap sent-username R3 password 7 1511021F0725
>
> router ospf 1
> network 137.1.3.3 0.0.0.0 area 0
> network 137.1.35.1 0.0.0.0 area 3
> network 137.1.63.3 0.0.0.0 area 3
> network 137.1.254.3 0.0.0.0 area 0
> neighbor 137.1.35.2 priority 1
>
> R5:
>
> interface BRI0/0
> ip address 137.1.35.2 255.255.255.252
> no ip directed-broadcast
> encapsulation ppp
> ip ospf network non-broadcast
> ip ospf demand-circuit
> dialer map ip 137.1.35.1 name R3 broadcast 8358661
> dialer-group 1
> isdn switch-type basic-5ess
> ppp quality 90
> ppp authentication pap
> ppp pap sent-username R5 password 7 05080F1C2243
>
> router ospf 1
> network 137.1.5.5 0.0.0.0 area 3
> network 137.1.35.2 0.0.0.0 area 3
> network 137.1.65.5 0.0.0.0 area 3
> neighbor 137.1.35.1 priority 1
>
> ------------------------------------------------------------------------
>
> I have continuously got the messages on both routers for each 30secs:
> *Mar 2 08:53:32: OSPF: Rcv hello from 137.1.3.3 area 3 from BRI0/0
> 137.1.35.1
> *Mar 2 08:53:32: OSPF: End of hello processing
> ------------------------------------------------------------------------
>
> I don't know why I use non-broadcast network type, the hello still
> occurs?
>
> Thanks for your regards.
>
> James
jr_chen.vcf
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:57 GMT-3