From: Jason T. Rohm (jtrohm@xxxxxxxxxxx)
Date: Mon Oct 02 2000 - 19:49:23 GMT-3
Abridged router configs:
hostname 3000B-R5
!
interface Async1
no ip address
encapsulation ppp
async dynamic routing
async mode dedicated
ipx network 615
no ipx route-cache
ipx watchdog-spoof
dialer in-band
dialer map ipx 615.0000.0c8e.acdf name 2513A-R6 modem-script DIAL broadcast
100
dialer map snapshot 1 name 2513A-R6 modem-script DIAL 100
dialer-group 2
snapshot server 5 dialer
ppp authentication chap pap
ppp chap password 7 11190E0A0516
ppp pap sent-username 3000B-R5 password 7 095C59060B01
!
access-list 901 deny sap any all any all
access-list 901 deny rip any all any all
access-list 901 permit any any all any all
!
dialer-list 2 protocol ipx list 901
!
line aux 0
modem InOut
modem autoconfigure type hayes_optima
rxspeed 38400
txspeed 38400
hostname 2513A-R6
!
interface Async1
no ip address
no ip directed-broadcast
encapsulation ppp
dialer in-band
dialer fast-idle 300
dialer map snapshot 1 name 3000B-R5 modem-script DIAL 101
dialer map ipx 615.0000.0c07.9817 name 3000B-R5 modem-script DIAL broadcast
101
dialer-group 2
async dynamic routing
async mode dedicated
ipx network 615
no ipx route-cache
ipx watchdog-spoof
ipx spx-spoof
snapshot client 5 120 dialer
ppp authentication chap pap LOCAL
ppp chap password 7 051B11003348
ppp pap sent-username 2513A-R6 password 7 044B1C091D25
!
access-list 901 deny any any sap any all
access-list 901 deny any any rip any all
access-list 901 permit any any all
!
dialer-list 2 protocol ipx list 901
line aux 0
modem InOut
modem autoconfigure type hayes_optima
speed 38400
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
Maljure, Sanjay
Sent: Monday, October 02, 2000 5:10 PM
To: 'Jason T. Rohm'; CCIE List
Subject: RE: Snapshot Routes Timeout
Hi
What code are u running? I tried this and it worked fine for me with 11.2
(19)
The routes stay in the routing table till the quiet time expires and then
there is a route exchange again during the active time. I tested with quiet
times up to 10 minutes.
If your configs are correct, check your code...
Apparently somebody else had a similar problem on the list and it went away
when they upgraded the code....
Thanks
Sanjay
-----Original Message-----
From: Jason T. Rohm [mailto:jtrohm@athenet.net]
Sent: Monday, October 02, 2000 5:27 PM
To: CCIE List
Subject: Snapshot Routes Timeout
I found a bunch of questions on this in the archive, but not any real
answers... so here goes...
I have snapshot routing setup on a DDR circuit (CCIE Prep Lab 7 for those of
you who have it).
The access-lists deny IPX Sap/Rip updates and permit all other IPX traffic.
At the end of the quiet period, the snapshot client will dial the server and
receive updates, however, as soon as the idle timer expires (active time + 2
mins), the line will drop (normal), but a show ipx route shows all snapshot
learned routes as being in holddown, as soon as the hold down expires, the
routes are aged out.
A debug of the snapshot server and client (debug snapshot) shows that the
snapshot server and client are atleast recognizing that routing updates are
coming in.
I have reviewed the code that CCIE Bootcamp sent me, and the only real
difference that I see is that they have the ends (server/client) reversed
which shouldn't really matter since it is not really a hub and spoke
configuration.
Anyone have ideas?
-Jason
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:23 GMT-3