From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Wed Sep 06 2000 - 13:27:26 GMT-3
Did the router boot up ok before you upgrade the memory? What version of
IOS are you trying to load? I believe you might need more that 8 Meg Ram
for some of the 11.3 or 12.0 images.
- Kevin
At 02:47 PM 9/6/00 +0100, you wrote:
>I have an error message displaying when a 4500 router I have borrowed boots up
. (See below). I have upgraded it from 4 to 8 Meg flash and it has the original
8 Meg of main memory in it. It will only come up in boot mode using config reg
2102 or 42. It functions as a frame relay switch okay (which will be its main
purpose) but doesn't seem to want to go pass the boot stage to give full routin
g functunality. I have tried different memory and running at only 4 meg but sti
ll the same problem. Can someone spot if I'm doing something silly wrong, or wh
at the problem might be.
>
>Also does anyone know if the 1000 series routers support dlsw in any IOS relea
ses?
>
>Thanks.
>
>ERRORS IN BOLD
>
>
>System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
>Copyright (c) 1994 by cisco Systems, Inc.
>C4500 processor with 8192 Kbytes of main memory
>
>
>*** System received a SegV exception ***
>signal= #b, code= #408, context= #60265ea0
>PC = 0x6002cb24, Cause = 0x420, Status Reg = 0x34408002
>
>System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
>Copyright (c) 1994 by cisco Systems, Inc.
>C4500 processor with 8192 Kbytes of main memory
>
>program load complete, entrypt: 0x80008000, size: 0x4eee18
>
>Error : memory requirements exceed available memory
>Memory required : 0x00CE1F54
>
>*** System received a Software forced crash ***
>signal= #17, code= #4, context= #0
>PC = 0x80008094, Cause = 0x20, Status Reg = 0x30408403
>
>System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
>Copyright (c) 1994 by cisco Systems, Inc.
>C4500 processor with 8192 Kbytes of main memory
>
>program load complete, entrypt: 0x80008000, size: 0x241850
>
> Restricted Rights Legend
>
>Use, duplication, or disclosure by the Government is
>subject to restrictions as set forth in subparagraph
>(c) of the Commercial Computer Software - Restricted
>Rights clause at FAR sec. 52.227-19 and subparagraph
>(c) (1) (ii) of the Rights in Technical Data and Computer
>Software clause at DFARS sec. 252.227-7013.
>
> cisco Systems, Inc.
> 170 West Tasman Drive
> San Jose, California 95134
>
>
>
>Cisco Internetwork Operating System Software
>IOS (tm) 4500 Bootstrap Software (C4500-XBOOT), Version 10.2(4a), RELEASE SOFT
WA
>RE (fc1)
>Copyright (c) 1986-1995 by cisco Systems, Inc.
>Compiled Mon 06-Mar-95 20:00 by kmac
>Image text-base: 0x60008760, data-base: 0x601CA000
>
>cisco 4500 (R4K) processor (revision B) with 8192K/4096K bytes of memory.
>Processor board serial number 01659220
>R4600 processor, Implementation 32, Revision 1.0
>X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
>Bridging software.
>G.703/E1 software, Version 1.0.
>2 Ethernet/IEEE 802.3 interfaces.
>4 Serial network interfaces.
>128K bytes of non-volatile configuration memory.
>8192K bytes of processor board System flash (Read/Write)
>4096K bytes of processor board Boot flash (Read/Write)
>
> --- System Configuration Dialog ---
>
>At any point you may enter a question mark '?' for help.
>Refer to the 'Getting Started' Guide for additional help.
>Use ctrl-c to abort configuration dialog at any prompt.
>Default settings are in square brackets '[]'.
>
>Would you like to enter the initial configuration dialog? [yes]: no
>
>
>
>
>
>
>
>
>Router(boot)>en
>Router(boot)#c
>% Ambiguous command: "c"
>Router(boot)#conf t
>Enter configuration commands, one per line. End with CNTL/Z.
>Router(boot)(config)#no service udp-small-servers
> ^
>% Invalid input detected at '^' marker.
>
>Router(boot)(config)#no service tcp-small-servers
>Router(boot)(config)#!
>Router(boot)(config)#hostname FrameSwitch
>FrameSwitch(boot)(config)#!
>FrameSwitch(boot)(config)#!
>FrameSwitch(boot)(config)#frame-relay switching
>FrameSwitch(boot)(config)#frame-relay switching
>FrameSwitch(boot)(config)#!
>FrameSwitch(boot)(config)#interface Serial0
>FrameSwitch(boot)(config-if)# no ip address
>FrameSwitch(boot)(config-if)# encapsulation frame-relay
>FrameSwitch(boot)(config-if)# clockrate 38400
>FrameSwitch(boot)(config-if)# clockrate 38400
>FrameSwitch(boot)(config-if)# clockrate 38400
>FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
>FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
>FrameSwitch(boot)(config-if)# frame-relay intf-type dce
>FrameSwitch(boot)(config-if)# frame-relay intf-type dce
>FrameSwitch(boot)(config-if)# frame-relay intf-type dce
>FrameSwitch(boot)(config-if)# frame-relay route 100 interface Serial1 101
>FrameSwitch(boot)(config-if)# frame-relay route 100 interface Serial1 101
>FrameSwitch(boot)(config-if)#!
>FrameSwitch(boot)(config-if)#interface Serial1
>FrameSwitch(boot)(config-if)# no ip address
>FrameSwitch(boot)(config-if)# encapsulation frame-relay
>FrameSwitch(boot)(config-if)# clockrate 19200
>FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
>FrameSwitch(boot)(config-if)# frame-relay intf-type dce
>FrameSwitch(boot)(config-if)# frame-relay route 101 interface Serial0 100
>FrameSwitch(boot)(config-if)#!
>FrameSwitch(boot)(config-if)#no ip classless
> ^
>% Invalid input detected at '^' marker.
>
>FrameSwitch(boot)(config-if)#!
>FrameSwitch(boot)(config-if)#line con 0
>FrameSwitch(boot)(config-line)#line aux 0
>FrameSwitch(boot)(config-line)#line vty 0 4
>FrameSwitch(boot)(config-line)# login
>FrameSwitch(boot)(config-line)#!
>FrameSwitch(boot)(config-line)#end
>FrameSwitch(boot)#
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:52 GMT-3