From: damien (damien@xxxxxxxxxxx)
Date: Wed Sep 06 2000 - 14:43:56 GMT-3
IOS too big.
----- Original Message -----
From: Eddie Jobson
To: ccielab@groupstudy.com
Sent: Wednesday, September 06, 2000 1:47 PM
Subject: 4500 problem
I have an error message displaying when a 4500 router I have
borrowed boots up. (See below). I have upgraded it from 4 to 8 Meg
flash and it has the original 8 Meg of main memory in it. It will
only come up in boot mode using config reg 2102 or 42. It functions
as a frame relay switch okay (which will be its main purpose) but
doesn't seem to want to go pass the boot stage to give full routing
functunality. I have tried different memory and running at only 4
meg but still the same problem. Can someone spot if I'm doing
something silly wrong, or what the problem might be.
Also does anyone know if the 1000 series routers support dlsw in
any IOS releases?
Thanks.
ERRORS IN BOLD
System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
Copyright (c) 1994 by cisco Systems, Inc.
C4500 processor with 8192 Kbytes of main memory
*** System received a SegV exception ***
signal= #b, code= #408, context= #60265ea0
PC = 0x6002cb24, Cause = 0x420, Status Reg = 0x34408002
System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
Copyright (c) 1994 by cisco Systems, Inc.
C4500 processor with 8192 Kbytes of main memory
program load complete, entrypt: 0x80008000, size: 0x4eee18
Error : memory requirements exceed available memory
Memory required : 0x00CE1F54
*** System received a Software forced crash ***
signal= #17, code= #4, context= #0
PC = 0x80008094, Cause = 0x20, Status Reg = 0x30408403
System Bootstrap, Version 5.2(4) [kmac 4], RELEASE SOFTWARE (fc1)
Copyright (c) 1994 by cisco Systems, Inc.
C4500 processor with 8192 Kbytes of main memory
program load complete, entrypt: 0x80008000, size: 0x241850
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134
Cisco Internetwork Operating System Software
IOS (tm) 4500 Bootstrap Software (C4500-XBOOT), Version 10.2(4a),
RELEASE SOFTWA
RE (fc1)
Copyright (c) 1986-1995 by cisco Systems, Inc.
Compiled Mon 06-Mar-95 20:00 by kmac
Image text-base: 0x60008760, data-base: 0x601CA000
cisco 4500 (R4K) processor (revision B) with 8192K/4096K bytes of
memory.
Processor board serial number 01659220
R4600 processor, Implementation 32, Revision 1.0
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
Bridging software.
G.703/E1 software, Version 1.0.
2 Ethernet/IEEE 802.3 interfaces.
4 Serial network interfaces.
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
4096K bytes of processor board Boot flash (Read/Write)
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Refer to the 'Getting Started' Guide for additional help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes]: no
Router(boot)>en
Router(boot)#c
% Ambiguous command: "c"
Router(boot)#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(boot)(config)#no service udp-small-servers
^
% Invalid input detected at '^' marker.
Router(boot)(config)#no service tcp-small-servers
Router(boot)(config)#!
Router(boot)(config)#hostname FrameSwitch
FrameSwitch(boot)(config)#!
FrameSwitch(boot)(config)#!
FrameSwitch(boot)(config)#frame-relay switching
FrameSwitch(boot)(config)#frame-relay switching
FrameSwitch(boot)(config)#!
FrameSwitch(boot)(config)#interface Serial0
FrameSwitch(boot)(config-if)# no ip address
FrameSwitch(boot)(config-if)# encapsulation frame-relay
FrameSwitch(boot)(config-if)# clockrate 38400
FrameSwitch(boot)(config-if)# clockrate 38400
FrameSwitch(boot)(config-if)# clockrate 38400
FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
FrameSwitch(boot)(config-if)# frame-relay intf-type dce
FrameSwitch(boot)(config-if)# frame-relay intf-type dce
FrameSwitch(boot)(config-if)# frame-relay intf-type dce
FrameSwitch(boot)(config-if)# frame-relay route 100 interface
Serial1 101
FrameSwitch(boot)(config-if)# frame-relay route 100 interface
Serial1 101
FrameSwitch(boot)(config-if)#!
FrameSwitch(boot)(config-if)#interface Serial1
FrameSwitch(boot)(config-if)# no ip address
FrameSwitch(boot)(config-if)# encapsulation frame-relay
FrameSwitch(boot)(config-if)# clockrate 19200
FrameSwitch(boot)(config-if)# frame-relay lmi-type ansi
FrameSwitch(boot)(config-if)# frame-relay intf-type dce
FrameSwitch(boot)(config-if)# frame-relay route 101 interface
Serial0 100
FrameSwitch(boot)(config-if)#!
FrameSwitch(boot)(config-if)#no ip classless
^
% Invalid input detected at '^' marker.
FrameSwitch(boot)(config-if)#!
FrameSwitch(boot)(config-if)#line con 0
FrameSwitch(boot)(config-line)#line aux 0
FrameSwitch(boot)(config-line)#line vty 0 4
FrameSwitch(boot)(config-line)# login
FrameSwitch(boot)(config-line)#!
FrameSwitch(boot)(config-line)#end
FrameSwitch(boot)#
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:24:52 GMT-3