From: David Goldsmith (dgoldsmi@xxxxxxxxx)
Date: Thu Jun 08 2000 - 14:08:30 GMT-3
Also thought you could spell over of....
Bridge Lat over Frame.
David Goldsmith wrote:
> Group,
>
> I am not a LAT expert..... But I thought you could only bridge Lat of Frame..
.
>
> I'll look this up a little later...
>
> Dave G.
>
> Brian Hescock wrote:
>
> > Please let me know how it goes after saving the config without the
> > mac-addr command and doing a reload. It could potentially have it in
> > memory still, just as frame pvc's are even after removing them from the
> > config and you have to reload the router to get rid of it.
> >
> > I've decoded the traceback and the error was in frame encapsulation (the
> > top of the stack is the most recent function):
> >
> > 0x3451230:_fr_encaps(0x303932c+0x417de6)+0x11e
> > 0x3450FB4:_fr_vencapsulate(0x303932c+0x417c6e)+0x1a
> > 0x30F4892:_pak_encap(0x303932c+0xbb542)+0x24
> > 0x363A7E4:_lat_pakout(0x303932c+0x601468)+0x50
> > 0x363A986:_of_message(0x303932c+0x60153c)+0x11e
> > 0x364524C:_toc_elapse(0x303932c+0x60be74)+0xac
> > 0x363AB10:_lat_timer(0x303932c+0x601720)+0xc4
> >
> > I'll try to see if I can find anything if I have some spare time today (I
> > test in less than three weeks... going nuts).
> >
> > Brian
> >
> > On Thu, 8 Jun 2000, Wang, Kai wrote:
> >
> > > I removed the mac-address command. I am still getting the same error
> > > message.
> > >
> > > %LINK-3-BADMACREG: Interface Serial1, non-existent MACADDR registry for l
ink
> > > 31
> > > -Process= "LAT Timers", ipl= 0, pid= 1
> > > -Traceback= 3451230 3450FB4 30F4892 363A7E4 363A986 364524C 363AB10
> > >
> > > -----Original Message-----
> > > From: Brian Hescock [mailto:bhescock@cisco.com]
> > > Sent: Thursday, June 08, 2000 11:44 AM
> > > To: Wang, Kai
> > > Cc: 'ccielab@groupstudy.com'
> > > Subject: Re: LAT over F/R
> > >
> > >
> > > Take off the mac-address command, the ios reference book indicates it's
> > > only used for token ring interfaces. I'm somewhat surprised you could
> > > configure it on a serial interface if it can only be used on token
> > > ring. I checked the lat configuration guide and there isn't anything in
> > > there about having to change the mac-address. The first error
> > > "BADMACREG" is probably related to the fact you tried changing the mac
> > > address. The second error is a traceback related to LAT Timers. The
> > > first error could have possibly caused the second error in the IOS code.
> > >
> > > Brian
> > >
> > > On Thu, 8 Jun 2000, Wang, Kai wrote:
> > >
> > > > I am trying to configure LAT over F/R without using the protocol
> > > > translation. I am unable to get it to work.
> > > >
> > > > The configs are shown as follows:
> > > >
> > > > R4 config
> > > > !
> > > > interface Serial1
> > > > mac-address 0004.0004.0004
> > > > no ip address
> > > > encapsulation frame-relay
> > > > lat enabled
> > > > !
> > > > lat service TEST enabled
> > > >
> > > > R3 config
> > > > !
> > > > interface Serial0
> > > > mac-address 0003.0003.0003
> > > > no ip address
> > > > encapsulation frame-relay
> > > > lat enabled
> > > > no fair-queue
> > > >
> > > > I am getting the following error message from my router:
> > > >
> > > > %LINK-3-BADMACREG: Interface Serial1, non-existent MACADDR registry for
> > > link
> > > > 31
> > > > -Process= "LAT Timers", ipl= 0, pid= 29
> > > > -Traceback= 3451230 3450FB4 30F4892 363A7E4 363A986 364524C 363AB10
> > > >
> > > > What should I do to get it to work?
> > > >
> > > > Thank You!
> > > >
> > > > Kai Wang
> > > > EDS - AHSMC/Network Operation
> > > > MS 3010
> > > > 300 East Big Beaver
> > > > Troy, MI 48083
> > > >
> > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:41 GMT-3