From: Hyper Boy (hyper_boy@xxxxxxxx)
Date: Thu May 18 2000 - 23:33:27 GMT-3
Hello, ATM NSAP-ADDRESS can configure entire ATM address and ATM ESI-ADDRESS ca
n configure the ESI portion (last 7 bytes) of the NSAP address.
I find that MAC-ADDRESS can not be configured on ATM interface correctly, I don
't know why?
If you use 1577 ARP-SERVER and 1483 SVC mapping, you can use ATM NSAP-ADDRESS c
ommand or ATM ESI-ADDRESS command to identify the ATM address. You are only all
ow to use one command.
----- Original Message -----
From: luoht <luoht@usa.net>
To: <ccielab@groupstudy.com>
Sent: Friday, May 19, 2000 10:01 AM
Subject: Re: LANE Question
> So, anyone can tell me what's the difference between 'mac-address zzzzzz'
> and 'atm nsap-address zzzzz' and/or 'atm esi-address zzzzz' ?
>
> Michael
>
> ----- Original Message -----
> From: "Muthu Mohanasundaram" <mmsundar@yahoo.com>
> To: "Scott F. Robohn" <sfr@ccci.com>; <ccielab@groupstudy.com>
> Sent: Thursday, May 18, 2000 8:16 AM
> Subject: Re: LANE Question
>
>
> > Hi Scott,
> >
> > Thanks for your reply. But I now have one more
> > question.
> >
> > If I have to explicitly configure my LECS atm address
> > on my router, for some reason, which command should I
> > use?
> >
> > atm nsap-address zzzzzz
> >
> > or
> >
> > lane config config-atm-address zzzzzzz
> >
> > or both ?
> >
> > Thanks,
> >
> > Mohan.
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > --- "Scott F. Robohn" <sfr@ccci.com> wrote:
> > > Muthu,
> > >
> > > These are the default NSAP addresses used for LANE
> > > components on a LANE module. The '**' gets filled
> > > in by the
> > > subinterface number you use for the particular LANE
> > > component.
> > >
> > > The point with these default addresses is to make it
> > > easier
> > > for you: you don't _have to_ enter any NSAP
> > > addresses (or
> > > parts of NSAP addresses). If ILMI is turned on, you
> > > automatically get an NSAP prefix (the first 13
> > > bytes) from
> > > the ATM switch, and this default scheme fills in the
> > > last 7
> > > bytes for you.
> > >
> > > Do you _want_ to use a different address? I would
> > > recommend
> > > against it. But if you have/want to, you can use
> > > the 'atm
> > > nsap-address zzzz...' or 'atm esi-address zzzz....'
> > > command
> > > on the subinterfaces where you don't want to use the
> > > default
> > > NSAP addresses. If you do this, be aware that you
> > > may need
> > > to hard-code 'atm route' entries in one or more ATM
> > > switches.
> > >
> > > HTH,
> > > Scott
> > >
> > > Muthu Mohanasundaram wrote:
> > > >
> > > > Hi All,
> > > >
> > > > The Catalyst 5000 manuals say the ESI part of the
> > > ATM
> > > > address for LANE components are :
> > > >
> > > > LEC = .......0.**
> > > > LES = .......1.**
> > > > BUS = .......2.**
> > > > LECS= .......3.00
> > > >
> > > > That is LEC has 0, LES has 1, BUS has 2 and LECS
> > > has 3
> > > > in the last byte of the ESI.
> > > >
> > > > Is this sequence a MUST for LANE to operate? Or
> > > are
> > > > these values are just given as Cisco defaults so
> > > that
> > > > they are easy to remember?
> > > >
> > > > My problem is, if I am configuring all these LANE
> > > > components with my own explicit atm addresses, do
> > > I
> > > > have to follow this sequence.
> > > >
> > > > For example if my LECS address is
> > > >
> > > > 47.0091810000......00.0061.705b.7702.00,
> > > >
> > > > can I use
> > > >
> > > > 47.0091810000......00.0061.705b.1111.** for my LES
> > > > 47.0091810000......00.0061.705b.2222.** for my BUS
> > > > 47.0091810000......00.0061.705b.3333.** for my LEC
> > > > on the same router ?
> > > >
> > > > Can someone point me to a good URL on this stuff.
> > > >
> > > > Any help would be appreciated.
> > > >
> > > > Thanks,
> > > >
> > > > Mohan.
> > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:30 GMT-3